User Panel
User Panel
User Panel
|
Posted: 10/19/2020 9:38:47 AM EDT
[Last Edit: KentuckyMarksman]
[#1]
My dad has been pinching his pennies for a PA10-65 ever since before the Gen3 came was announced. He got a Gen 2 lower, and finally purchased a Gen3 upper. He asked me to install his scope on it for him. I currently have the rifle in my possession.
While looking over the rifle, I noticed that something may be mis-aligned. The gas block is almost touching the handguard on 1 side, and has a ton of room on the opposite side. If I apply a tiny bit of force, then the gas block touches the inside of the rail. Is this normal for the PA10 rifles? I'm concerned about it touching while firing and causing accuracy issues. if it's purely cosmetic, then I don't want to mention it to my dad and have him worry about it. I've included a picture below. @palmettostatearmory  Edit: I got another picture/ 
|
|
|
|
|
Posted: 10/20/2020 9:59:41 AM EDT
[Last Edit: PalmettoStateArmory]
[#2]
Quote HistoryOriginally Posted By KentuckyMarksman: My dad has been pinching his pennies for a PA10-65 ever since before the Gen3 came was announced. He got a Gen 2 lower, and finally purchased a Gen3 upper. He asked me to install his scope on it for him. I currently have the rifle in my possession. While looking over the rifle, I noticed that something may be mis-aligned. The gas block is almost touching the handguard on 1 side, and has a ton of room on the opposite side. If I apply a tiny bit of force, then the gas block touches the inside of the rail. Is this normal for the PA10 rifles? I'm concerned about it touching while firing and causing accuracy issues. if it's purely cosmetic, then I don't want to mention it to my dad and have him worry about it. I've included a picture below. @palmettostatearmory https://i.imgur.com/F1nbySA.jpg Edit: I got another picture/ https://i.imgur.com/857o0WY.jpg PM Sent. Thanks, Josiah |
|
|
|
FL, USA
|
Posted: 10/25/2020 10:38:54 AM EDT
[#3]
I have a PSA Gen2 completed lower, been waiting on a 16" Nitrided , or Chrome upper to come in stock, but have been waiting. Are 16" discontinued forever?
|
|
|
|
Posted: 10/26/2020 9:37:53 AM EDT
[#4]
Quote HistoryOriginally Posted By MaverickCowboy: I have a PSA Gen2 completed lower, been waiting on a 16" Nitrided , or Chrome upper to come in stock, but have been waiting. Are 16" discontinued forever? Not forever. The demand right now is for 18" 20" for hunting. I do not have an eta for 16" 308 barrels. Thank you, Josiah |
|
|
|
USA
|
Posted: 11/18/2020 10:19:57 PM EDT
[#5]
Will the Geissele 7.62 charging handle work with the PA10? Will the buffer extension work with a Magpul PRS?
|
|
|
SC, USA
|
Posted: 11/24/2020 1:21:05 PM EDT
[#6]
The charging handle does. Not sure on the other
|
|
|
USA
|
Posted: 12/25/2020 1:47:24 PM EDT
[#7]
Quote HistoryOriginally Posted By Salvadorsshadow: Will the Geissele 7.62 charging handle work with the PA10? Will the buffer extension work with a Magpul PRS? As stated by the poster above, yes the Geissele 7.62 CH will work. Regarding the extension working with the Magpul PRS, it depends which extension you have. If you have an A2/rifle buffer extension or standard AR carbine extension, yes it will work. Magpul also says a Vltor A5 stock will fit. If you have one of the PSA extended buffer tubes, which are slightly extended to use a standard carbine spring and buffer on 308 ARs, I have no idea. |
|
|
|
Posted: 12/25/2020 2:08:52 PM EDT
[#8]
If I want to put an A2 but stock on a Gen 3, will a standard A2 buffer and spring work?
|
|
|
|
|
Posted: 12/28/2020 11:45:34 AM EDT
[#9]
Quote HistoryOriginally Posted By EagleArmsHBAR: If I want to put an A2 but stock on a Gen 3, will a standard A2 buffer and spring work? You will need the 308 A2 buffer and a 308 spring. They are different than the standard AR15 A2 ones. Thank you, Josiah |
|
|
|
FL, USA
|
Posted: 1/13/2021 12:14:31 AM EDT
[#10]
any updates on upper parts kits for the PA10? Finally found a stripped upper but would love to finish the build.
|
|
|
|
Posted: 1/13/2021 3:43:05 PM EDT
[Last Edit: craig24680]
[#11]
Any rough ETA on gen3 PA10 (or PA65) kits being for sale?
|
|
|
|
TX, USA
|
Posted: 1/15/2021 9:33:36 PM EDT
[#12]
@palmettostatearmory
Having looked around on the web and on outofbattery it seems to be that the PSA-10 gen2 uppers have a quasi dpms low height. I have the 12.5” pistol PSA-10 with the 10” hand guards but I really want a 12” handguard to nestle up closer to my suppressor. What brand mlok handguards work with the PSA uppers? I could honestly be over thinking this but I’d rather ask before I pull the proverbial trigger on a purchase |
|
|
|
Posted: 1/18/2021 9:22:01 AM EDT
[#13]
Quote HistoryOriginally Posted By speedtrucker: @palmettostatearmory Having looked around on the web and on outofbattery it seems to be that the PSA-10 gen2 uppers have a quasi dpms low height. I have the 12.5” pistol PSA-10 with the 10” hand guards but I really want a 12” handguard to nestle up closer to my suppressor. What brand mlok handguards work with the PSA uppers? I could honestly be over thinking this but I’d rather ask before I pull the proverbial trigger on a purchase We aren't DPMS high or low. We are more towards low spectrum. I don't have a list of ones that work exactly with ours. I would take it into a more tactical gun shop and line up a few different brands to see what fits closest. Some of the guys here and in the variants section may have more experience as well. Thank you, Josiah |
|
|
|
|
Posted: 1/18/2021 9:28:05 AM EDT
[#14]
Quote HistoryOriginally Posted By speedtrucker: @palmettostatearmory Having looked around on the web and on outofbattery it seems to be that the PSA-10 gen2 uppers have a quasi dpms low height. I have the 12.5” pistol PSA-10 with the 10” hand guards but I really want a 12” handguard to nestle up closer to my suppressor. What brand mlok handguards work with the PSA uppers? I could honestly be over thinking this but I’d rather ask before I pull the proverbial trigger on a purchase @speedtrucker Be careful with leaving yourself enough room to comfortably work the suppressors locking system if it's not direct thread. |
|
|
|
TX, USA
|
Posted: 1/20/2021 12:15:52 AM EDT
[#15]
Quote HistoryOriginally Posted By Wangstang: @speedtrucker Be careful with leaving yourself enough room to comfortably work the suppressors locking system if it's not direct thread. Yeah I don’t need flush fit or recessed, I’m looking more for a 12” hand guard that’ll sit about .5” shorter than my current 12.5” barrel. It’s the same idea as my 10.5” 300blk with a 10” HG, my sandman mounts and there’s about .4-.5” of clearance between the two |
|
|
FL, USA
|
Posted: 1/30/2021 12:12:08 PM EDT
[#16]
Quote HistoryOriginally Posted By vedubin01: any updates on upper parts kits for the PA10? Finally found a stripped upper but would love to finish the build. Didn't seem to get an answer on when, so are other companies upper parts kits compatible with the PA10 upper? |
|
|
|
Posted: 2/8/2021 9:37:20 PM EDT
[#17]
@PalmettoStateArmory
Got my complete upper, LPK in and Lower at the FFL waiting. First impressions of the upper is that it's big and heavy which I wanted, bench gun. Question on the gen3 adjustable gas block, this is my first ever adjustable gas block so excuse the dumb question. Which way do I screw it in for less/more gas? Is there a manual you all have, even PDF, with this info? Thanks, |
|
|
|
|
Posted: 2/9/2021 10:32:34 AM EDT
[#18]
Quote HistoryOriginally Posted By craig24680: @PalmettoStateArmory Got my complete upper, LPK in and Lower at the FFL waiting. First impressions of the upper is that it's big and heavy which I wanted, bench gun. Question on the gen3 adjustable gas block, this is my first ever adjustable gas block so excuse the dumb question. Which way do I screw it in for less/more gas? Is there a manual you all have, even PDF, with this info? Thanks, Please PM me your order number and I will be able to help you out. Thank you, Josiah |
|
|
|
AK, USA
|
Posted: 2/10/2021 7:10:45 PM EDT
[Last Edit: Nomad91]
[#19]
Can anyone tell me what parts are compatible for the TD/pivot pins, bolt catch and mag catch? Doesn’t seem like psa will be selling the upgrade kit and I feel like $200+ shipped is a bit much for the LBK right now. Would be nice to get a stripped or assembled upper as well if at all possible.
Thanks |
|
|
|
Posted: 2/15/2021 10:49:00 AM EDT
[#20]
Quote HistoryOriginally Posted By Nomad91: Can anyone tell me what parts are compatible for the TD/pivot pins, bolt catch and mag catch? Doesn’t seem like psa will be selling the upgrade kit and I feel like $200+ shipped is a bit much for the LBK right now. Would be nice to get a stripped or assembled upper as well if at all possible. Thanks If you PM me your order number, I will send you the pins, bolt catch assembly and a mag catch assembly. Thank you, Josiah |
|
|
|
MT, USA
|
Posted: 2/19/2021 11:52:10 PM EDT
[Last Edit: Blacksavage70]
[#21]
Gen 2 classic lower with an a2 tube, buffer, and spring. Gen 2 .308 upper. Bolt is leaving four marks in the lower, and experiencing a failure to feed after the initial shot. Try the quarters in the bottom of the tube truck?
Edited update; The rifle spring and buffer I’m running are the DPMS ones. Added the two quarters, no dice. Side by side comparison of that spring with an ar-15 rifle spring shows the 15 spring being a little longer, swapped that one out with my ar-10 rifle spring and its cycling as it should now, at least it did for the five rounds I put through it. Run it with the ar-15 spring or will it have adverse effects I’m unaware of? Edit number 2; Tinkering with the extractor, I removed one of the O-rings- it now runs as it should with the DPMS buffer&spring with no quarters in the tube, however the bolt won’t lock back on any empty mag when firing-it will when operating the CH manually |
|
|
|
Posted: 3/8/2021 4:23:00 PM EDT
[#22]
Quote HistoryOriginally Posted By PalmettoStateArmory: If you PM me your order number, I will send you the pins, bolt catch assembly and a mag catch assembly. Thank you, Josiah Quote HistoryOriginally Posted By PalmettoStateArmory: Originally Posted By Nomad91: Can anyone tell me what parts are compatible for the TD/pivot pins, bolt catch and mag catch? Doesn’t seem like psa will be selling the upgrade kit and I feel like $200+ shipped is a bit much for the LBK right now. Would be nice to get a stripped or assembled upper as well if at all possible. Thanks If you PM me your order number, I will send you the pins, bolt catch assembly and a mag catch assembly. Thank you, Josiah I am in this same situation as well, I finally assembled all the parts for my PA-10 Gen 2 build, and these are the last parts I need. send me an IM if you like. Thanks! |
|
|
|
|
Posted: 3/8/2021 5:52:12 PM EDT
[#23]
Quote HistoryOriginally Posted By Blacksavage70: Gen 2 classic lower with an a2 tube, buffer, and spring. Gen 2 .308 upper. Bolt is leaving four marks in the lower, and experiencing a failure to feed after the initial shot. Try the quarters in the bottom of the tube truck? Edited update; The rifle spring and buffer I’m running are the DPMS ones. Added the two quarters, no dice. Side by side comparison of that spring with an ar-15 rifle spring shows the 15 spring being a little longer, swapped that one out with my ar-10 rifle spring and its cycling as it should now, at least it did for the five rounds I put through it. Run it with the ar-15 spring or will it have adverse effects I’m unaware of? Edit number 2; Tinkering with the extractor, I removed one of the O-rings- it now runs as it should with the DPMS buffer&spring with no quarters in the tube, however the bolt won’t lock back on any empty mag when firing-it will when operating the CH manually If you would like us to take a look at it to get it running 100%, feel free to IM me. Thank you, Josiah |
|
|
|
|
Posted: 3/8/2021 5:52:42 PM EDT
[#24]
Quote HistoryOriginally Posted By 1paintball: I am in this same situation as well, I finally assembled all the parts for my PA-10 Gen 2 build, and these are the last parts I need. send me an IM if you like. Thanks! Please IM me your order number and I can get you taken care of. Thank you, Josiah |
|
|
|
|
Posted: 3/9/2021 7:26:58 PM EDT
[Last Edit: 1paintball]
[#25]
Quote HistoryOriginally Posted By SageEBR: Welcome to my world. I bought a brand new complete gen2 lower over a year ago and have been asking for non-stainless barrels ever since. I actually already bought a non-psa barrel I liked on black friday, at this point I am just planning to buy a complete gen3 upper, remove the barrel and add the new one but it has been so long I have to build the funds for that again as I used them for something else in the meantime. It would be awesome to see a complete upper kit minus the barrel but I imagine that won't happen since they will never say what barrels actually should work with their parts. Hopefully I can recoup some of that additional costs by selling the barrel on the EE. |
|
|
|
TX, USA
|
Posted: 4/8/2021 9:46:15 PM EDT
[#26]
I have the PSA AR47 10.5. Love the thing suppressed. Am I able to use the lower with a 9x39 upper? Thank you. Keep all the great products coming.
|
|
|
|
Posted: 4/9/2021 1:19:32 AM EDT
[#27]
Quote HistoryOriginally Posted By 1paintball: Quote HistoryOriginally Posted By 1paintball: Originally Posted By SageEBR: Welcome to my world. I bought a brand new complete gen2 lower over a year ago and have been asking for non-stainless barrels ever since. I actually already bought a non-psa barrel I liked on black friday, at this point I am just planning to buy a complete gen3 upper, remove the barrel and add the new one but it has been so long I have to build the funds for that again as I used them for something else in the meantime. It would be awesome to see a complete upper kit minus the barrel but I imagine that won't happen since they will never say what barrels actually should work with their parts. Hopefully I can recoup some of that additional costs by selling the barrel on the EE. For the record, the ballistic advantage barrel swap went well and I have no regrets. |
|
|
|
|
Posted: 4/9/2021 5:42:35 PM EDT
[#28]
Quote HistoryOriginally Posted By SageEBR: For the record, the ballistic advantage barrel swap went well and I have no regrets. Good to hear! Depending on how mine shoots when I can make time to work up loads I might do a swap. |
|
|
|
|
Posted: 4/14/2021 12:07:23 PM EDT
[Last Edit: PalmettoStateArmory]
[#29]
PA10 stripped uppers are in stock now!
https://palmettostatearmory.com/psa-pa10-gen3-complete-upper-receiver.html Thanks, Josiah |
|
|
|
TX, USA
|
Posted: 4/16/2021 12:53:02 PM EDT
[#30]
Just recently purchased a new Gen 3 lower (5165490563) and 20" upper (516540770) from the gun show and in the process of getting it outfitted and collecting ammo when I can find it a descent price. I will be using a Saker 7.62 suppressor and have questions about the adjustable gas block. I know it is preset for use un-suppressed at the factory and without using up ammo, which direction will go when I need to make adjustments. Does turning it in (to the right) increase or decrease the gas and is there a good starting point other then where it is set now to begin. Thanks in advance.
|
|
|
NV, USA
|
Posted: 4/30/2021 1:57:54 AM EDT
[#31]
Any chance of us getting PA10 pistol uppers and lowers?
|
|
|
|
Posted: 5/13/2021 11:11:42 PM EDT
[#32]
Have a larue trigger coming for my psa p10
Which ambi charging handle works and wouldn't break the bank? And I've heard the strike industries recoil spring is nice, is it gtg for the gen3? |
|
|
|
AR, USA
|
Posted: 7/10/2021 8:44:49 AM EDT
[Last Edit: 4356]
[#33]
Probably wouldn't be allowed, but a collection of what uppers fit what lowers would be nice.......
Doesnt look like PSA will have some lower priced uppers in the near future. Lowers are cheap. In searching, looks like not much is going to fit..... |
|
|
|
Posted: 7/29/2021 11:53:36 AM EDT
[#34]
Quote HistoryOriginally Posted By craig24680: Have a larue trigger coming for my psa p10 Which ambi charging handle works and wouldn't break the bank? And I've heard the strike industries recoil spring is nice, is it gtg for the gen3? I installed this ambi charging handle on a Gen3 PA65 upper. Works fine with no issues: https://www.aeroprecisionusa.com/ar308-ambi-charging-handle |
|
|
|
|
Posted: 8/3/2021 8:24:12 PM EDT
[#35]
Quote HistoryOriginally Posted By Salvadorsshadow: Will the Geissele 7.62 charging handle work with the PA10? Will the buffer extension work with a Magpul PRS? Do yourself a favor and use the rifle tube and rifle buffer under the PRS. Smoother recoil, especially if you use a superior-quality buffer like the CTS Engineering Aktiv buffer. More than worth the money, I put them on EVERY AR-pattern rifle I build. CTS Buffer He is a small shop, and it takes a few weeks for him to get the buffer built and shipped. He's a great guy, and worth doing business with. |
|
|
|
|
Posted: 8/3/2021 8:26:46 PM EDT
[#36]
Quote HistoryOriginally Posted By PalmettoStateArmory: We aren't DPMS high or low. We are more towards low spectrum. I don't have a list of ones that work exactly with ours. I would take it into a more tactical gun shop and line up a few different brands to see what fits closest. Some of the guys here and in the variants section may have more experience as well. Thank you, Josiah Quote HistoryOriginally Posted By PalmettoStateArmory: Originally Posted By speedtrucker: @palmettostatearmory Having looked around on the web and on outofbattery it seems to be that the PSA-10 gen2 uppers have a quasi dpms low height. I have the 12.5” pistol PSA-10 with the 10” hand guards but I really want a 12” handguard to nestle up closer to my suppressor. What brand mlok handguards work with the PSA uppers? I could honestly be over thinking this but I’d rather ask before I pull the proverbial trigger on a purchase We aren't DPMS high or low. We are more towards low spectrum. I don't have a list of ones that work exactly with ours. I would take it into a more tactical gun shop and line up a few different brands to see what fits closest. Some of the guys here and in the variants section may have more experience as well. Thank you, Josiah Odin Works low is one of the best fitting, also incredibly light and strong. I have them on four PA-10 guns, three generations of receiver sets. |
|
|
|
|
Posted: 8/17/2021 5:05:29 PM EDT
[#37]
Any brand of 80% lowers that work with the Gen 3 uppers?
@palmettostatearmory |
|
|
|
|
Posted: 8/18/2021 2:02:28 PM EDT
[#38]
Quote HistoryOriginally Posted By bikertrash: Any brand of 80% lowers that work with the Gen 3 uppers? @palmettostatearmory I do not know which one would work with ours. I would suggest contacting the different 80% manufacturers and asking them which ones they are designed to work with. Thank you, Josiah |
|
|
|
|
Posted: 8/22/2021 4:28:33 PM EDT
[#39]
Thank You Josiah!
What platform are your Gen 2 and Gen 3 uppers based on? @palmettostatearmory |
|
|
|
|
Posted: 8/23/2021 9:35:19 AM EDT
[#40]
Quote HistoryOriginally Posted By bikertrash: Thank You Josiah! What platform are your Gen 2 and Gen 3 uppers based on? @palmettostatearmory It is our own platform. We are neither DPMS high, DPMS low etc. Thank you, Josiah |
|
|
|
VA, USA
|
Posted: 9/23/2021 11:18:00 AM EDT
[#41]
Is the grip screw on the gen 3 a 1/4 x 28?
I was assembling one and the screw would not thread into the lower. Did a little damage to the lower, but should be ok. Thanks. |
|
|
|
Posted: 1/4/2022 1:51:21 AM EDT
[#42]
I want to buy a PSA Gen3 PA10 20" Rifle Length .308 WIN 1/10 Nitride 15" Lightweight M-lok Upper - With BCG & CH.
It was listed as being out of stock. I received an email from you guys - Jan 3 at 5:50 AM Palmetto State Armory BACK IN STOCK PSA Gen3 PA10 20" Rifle Length .308 WIN 1/10 Nitride 15" Lightweight M-lok Upper - With BCG & CH is back in stock! Sorry about the wait, but we've restocked. I went to order it and it's fucking out of stock. What kind of bullshit is this? Do I have to sit on the computer all day clicking on my email waiting for it to come back in stock again? |
|
|
|
|
Posted: 1/7/2022 4:25:07 PM EDT
[#43]
Quote HistoryOriginally Posted By gsparks: It was the ejector pin that broke. I took the pin and ejector and the dented bullets to the store for proof. I still have the bullets. Sounds like a near miss, you're lucky to still have a face. At least that's something very unlikely to repeat. |
|
|
|
|
Posted: 1/7/2022 4:33:51 PM EDT
[Last Edit: TheRiddleOfSteel]
[#44]
Edit: nevermind, found the answer. Someone sent me a pic of theirs.
|
|
|
|
OR, USA
|
Posted: 1/30/2022 12:09:45 AM EDT
[#45]
Will there be 16 inch 308 barrels or uppers again?
|
|
|
OR, USA
|
Posted: 1/30/2022 4:20:36 PM EDT
[#46]
Quote HistoryOriginally Posted By Donut777donut: Will there be 16 inch 308 barrels or uppers again? @PalmettoStateArmory |
|
|
|
Posted: 1/31/2022 11:13:36 AM EDT
[#47]
Quote HistoryOriginally Posted By Donut777donut: Will there be 16 inch 308 barrels or uppers again? We will in the future, but I do not have an eta at the moment. Thank you, Josiah |
|
|
|
USA
|
Posted: 2/26/2022 11:43:19 PM EDT
[#48]
Any plans to make parts for the DPMS G2?
|
|
|
VA, USA
|
Posted: 2/27/2022 12:46:59 AM EDT
[#49]
Quote HistoryOriginally Posted By PalmettoStateArmory: PM Sent. Thanks, Josiah Wanna answer the question out loud now? |
|
|
|
Posted: 6/20/2022 7:13:42 AM EDT
[#50]
I really like my gen 3 .308.
My only complaint is that there is no factory short barrel. I really want a factory 16" or 14.5" to P&W. |
|
|
|
AR15.COM is the world's largest firearm community and is a gathering place for firearm enthusiasts of all types.
From hunters and military members, to competition shooters and general firearm enthusiasts, we welcome anyone who values and respects the way of the firearm.
Subscribe to our monthly Newsletter to receive firearm news, product discounts from your favorite Industry Partners, and more.
Copyright © 1996-2024 AR15.COM LLC. All Rights Reserved.
Any use of this content without express written consent is prohibited.
AR15.Com reserves the right to overwrite or replace any affiliate, commercial, or monetizable links, posted by users, with our own.
