Archived Posts » 59,859,448
Are your dedicated 9mm lowers currently in stock?
11/18/2011 5:30:29 PM
The ones for $175 that are stripped except for the specific 9mm parts?
I am very close to ordering.
Thanks, John
I am very close to ordering.
Thanks, John
11/20/2011 7:51:29 PM
Call them on the phone and ask...fastest answer.
11/20/2011 8:04:16 PM
That isn't as fun
11/21/2011 12:55:52 PM
Good point....
Last year I bought the lower you are looking at, lower with parts kit but no stock. Its been GREAT and for me the best value out there.
11/23/2011 12:16:47 PM
Bump, as this is relevant to my interests too. 
Of course CMMG could just tell us they are in stock at Arfcom sponsor Brownells, for $174.99 and 'protect' their distributor/dealer network.
9mm lower at Brownells
Of course CMMG could just tell us they are in stock at Arfcom sponsor Brownells, for $174.99 and 'protect' their distributor/dealer network.
9mm lower at Brownells
11/24/2011 10:30:55 PM
FYI ordered one from CMMG's website today.......thanks.
11/26/2011 8:16:31 AM
I got a complete 9mm dedicated lower from Bud's Gun Shop recently. It looks great, now I just need the extra cash for an upper (and eventually a tax stamp), and I will be set.
11/26/2011 5:25:44 PM
That looks nice.
The holes on the side...I assume they are for retaining devices that hole the deef ramp and ejector in place. Are they pins or screws that hold them in place? Maybe a screw for the ejector and a pin for the feedramp???
Thanks!
The holes on the side...I assume they are for retaining devices that hole the deef ramp and ejector in place. Are they pins or screws that hold them in place? Maybe a screw for the ejector and a pin for the feedramp???
Thanks!
11/26/2011 7:20:51 PM
Originally Posted By HK_DUDE:
That looks nice.
The holes on the side...I assume they are for retaining devices that hole the deef ramp and ejector in place. Are they pins or screws that hold them in place? Maybe a screw for the ejector and a pin for the feedramp???
Thanks!
That looks nice.
The holes on the side...I assume they are for retaining devices that hole the deef ramp and ejector in place. Are they pins or screws that hold them in place? Maybe a screw for the ejector and a pin for the feedramp???
Thanks!
You are correct about what they are for. They are both roll pins.
11/26/2011 7:22:14 PM
How about the holes from the bottom?
11/27/2011 11:33:51 AM
Originally Posted By HK_DUDE:
How about the holes from the bottom?
How about the holes from the bottom?
I can't tell, the front one is about two inches deep, the rear one is deeper, longer than the allen wrench I used to test it. I can't see into them, even with the light I had on hand, well enough to tell what is in there.
11/27/2011 12:17:42 PM
Originally Posted By Landric:
I can't tell, the front one is about two inches deep, the rear one is deeper, longer than the allen wrench I used to test it. I can't see into them, even with the light I had on hand, well enough to tell what is in there.
Originally Posted By HK_DUDE:
How about the holes from the bottom?
How about the holes from the bottom?
I can't tell, the front one is about two inches deep, the rear one is deeper, longer than the allen wrench I used to test it. I can't see into them, even with the light I had on hand, well enough to tell what is in there.
Thanks for checking.......
