User Panel
User Panel
User Panel
PA, USA
|
Posted: 12/11/2023 6:19:47 PM EDT
Are there any hand stops out there that will fit this rail?
|
|
|
|
Posted: 12/11/2023 8:22:36 PM EDT
[Last Edit: WTFShane]
[#1]
Impact Weapons Components, but no longer see it on their website.
Edit: I had the handguard before. I used an extra rail nut piece to use a Larue handstop. |
|
|
|
|
Posted: 12/11/2023 8:54:43 PM EDT
[Last Edit: TGWLDR]
[#2]
There's a few archived threads here and on TOS outlining modding the Larue hand stops.
Edit: ONE HERE |
|
|
|
KY, USA
|
Posted: 12/12/2023 7:47:12 AM EDT
[#3]
Modified BCM KAG:
 |
|
|
|
Posted: 12/12/2023 9:06:21 AM EDT
[#4]
I have one on my 22lr rifle.
I don't remember where I got it or the make. I'll post a picture, hopefully someone will recognize it.  Attached File Attached File |
|
|
|
PA, USA
|
Posted: 12/12/2023 11:51:29 AM EDT
[#5]
Quote HistoryOriginally Posted By TGWLDR: There's a few archived threads here and on TOS outlining modding the Larue hand stops. Edit: ONE HERE Thank you. |
|
|
|
Posted: 12/12/2023 8:54:31 PM EDT
[#6]
Quote HistoryOriginally Posted By aod886: I have one on my 22lr rifle. I don't remember where I got it or the make. I'll post a picture, hopefully someone will recognize it. https://www.ar15.com/media/mediaFiles/249712/4_5in_22lr_Upper__7__jpg-3057243.JPG https://www.ar15.com/media/mediaFiles/249712/4_5in_22lr_Upper__6__jpg-3057244.JPG Impact Weapons Components |
|
|
|
|
Posted: 12/12/2023 9:13:35 PM EDT
[Last Edit: aod886]
[#7]
Quote HistoryOriginally Posted By WTFShane: Impact Weapons Components This is why I love this place! So after your post, I went and looked again. Sure enough, it is.  Attached FileImpact Weapons Components Edit: No retail directly from their site at this time. |
|
|
|
PA, USA
|
Posted: 12/14/2023 9:32:42 PM EDT
[#8]
Quote HistoryOriginally Posted By aod886: This is why I love this place! So after your post, I went and looked again. Sure enough, it is. https://www.ar15.com/media/mediaFiles/249712/20231212_201041_jpg-3057931.JPG Impact Weapons Components Edit: No retail directly from their site at this time. Do any other sites sell them? |
|
|
PA, USA
|
Posted: 12/21/2023 7:04:53 PM EDT
[#9]
Quote HistoryOriginally Posted By RangeToy: Do any other sites sell them? Guess not |
|
|
|
Posted: 12/21/2023 11:47:43 PM EDT
[#10]
Quote HistoryOriginally Posted By RangeToy: Guess not It's old and discontinued. You're better off putting WTB ads and scrounging classifieds/equipment exchange. |
|
|
|
|
Posted: 12/22/2023 12:03:30 AM EDT
[#11]
Quote HistoryOriginally Posted By RangeToy: Guess not Not that I've found. |
|
|
|
PA, USA
|
Posted: 1/25/2024 9:31:32 PM EDT
[#12]
Quote HistoryHow did you modify it? |
|
|
KY, USA
|
Posted: 1/26/2024 10:14:51 AM EDT
[#13]
Quote HistoryOriginally Posted By RangeToy: How did you modify it? Started with the keymod version, ground the nub in the middle flat, then ran it through the table saw leaving two ridges that fit the grooves in the alpha The bolt needs to be longer: 10-32 x 1-1/2" worked for me. You might need to grind a little off the end or add a lock washer if your barrel is fatter than gov profile Backing nut came from Noveske, they were making alpha parts for a while but I can't find them on their website. Any flat nut large enough will probably work though https://www.mcmaster.com/products/slot-nuts/low-profile-narrow-base-weld-nuts-8/ The only difference is that the Noveske backing nut fits into the hole in the alpha to prevent movement. Not sure how important that is. The hand stop really locks into the rail if the grooves are cut right |
|
|
PA, USA
|
Posted: 1/26/2024 11:48:12 AM EDT
[#14]
Quote HistoryOriginally Posted By scottr: Started with the keymod version, ground the nub in the middle flat, then ran it through the table saw leaving two ridges that fit the grooves in the alpha The bolt needs to be longer: 10-32 x 1-1/2" worked for me. You might need to grind a little off the end or add a lock washer if your barrel is fatter than gov profile Backing nut came from Noveske, they were making alpha parts for a while but I can't find them on their website. Any flat nut large enough will probably work though https://www.mcmaster.com/products/slot-nuts/low-profile-narrow-base-weld-nuts-8/ The only difference is that the Noveske backing nut fits into the hole in the alpha to prevent movement. Not sure how important that is. The hand stop really locks into the rail if the grooves are cut right Thanks! |
|
|
Win a FREE Membership!
Sign up for the ARFCOM weekly newsletter and be entered to win a free ARFCOM membership. One new winner* is announced every week!
You will receive an email every Friday morning featuring the latest chatter from the hottest topics, breaking news surrounding legislation, as well as exclusive deals only available to ARFCOM email subscribers.
AR15.COM is the world's largest firearm community and is a gathering place for firearm enthusiasts of all types.
From hunters and military members, to competition shooters and general firearm enthusiasts, we welcome anyone who values and respects the way of the firearm.
Subscribe to our monthly Newsletter to receive firearm news, product discounts from your favorite Industry Partners, and more.
Copyright © 1996-2024 AR15.COM LLC. All Rights Reserved.
Any use of this content without express written consent is prohibited.
AR15.Com reserves the right to overwrite or replace any affiliate, commercial, or monetizable links, posted by users, with our own.
