User Panel
Posted: 4/21/2024 7:11:25 PM EDT
I may have screwed up my shaft on my little Woods 48" hog. Went to sharpen the blades by jacking up the rear and setting on jack stands. Did the job but upon setting it down it looks like I had the male end (I had seperated the two halves) of the PTO shaft had been pinched against the framework of the mower as I jacked it up. Doesn't look obviously bent or distorted but now I can't slide the two halves together all the way. Goes about halfway there then stops. Like something isn't quite right. I also cannot get the connection "started" in any other orientation other than one. Weird. The tubing is the triangular-ish in cross section stuff and I would think I could get it together any way. Someone please advise. Stuff's growing fast and I need my mower...
|
|
|
Look for a burr
Use a file to remove it if you find one Add grease Hope that helps. |
|
|
Why sharpen bush hog blades? They are whirling hammers of doom. One row of a field, or one stump, or one rock and they will return to their natural state.
|
|
|
|
|
The two halves of the PTO shaft I have only go together in one orientation. There's one "lobe" that is a little different than the other two - if that makes sense.
|
|
|
I also don't sharpen mine.
I'd rather have a small tree get busted up than cut. Cutting it leaves it pointy, smashed leaves it blunt and less likely to puncture a tire. Not my idea - I read it somewhere. |
|
|
Originally Posted By rktman26: The two halves of the PTO shaft I have only go together in one orientation. There's one "lobe" that is a little different than the other two - if that makes sense. View Quote This. One side of the triangle shaped shaft may have a flat top too it rather then being rounded. Much easier then finding the internal spline that is slightly larger then all the others like New Holland did on my baler. |
|
"Freedom is a light for which many men have died in darkness".
George Washington "There comes a point where we are no longer drawing lines in the sand but are backed against a precipice." Orracle |
I sharpen mine. Don't get them as sharp as my lawn mower blades but do clean up the blades for mowing. I don't mow much in the way of thick brush though.
|
|
"It behooves every man to remember that the work of the critic is of altogether secondary importance, and that, in the end, progress is accomplished by the man who does things."
Theodore Roosevelt |
You may have dented your pto shaft guard.
|
|
|
I sharpen the blades on my brush hog a couple times a year, very easy to raise it up and crawl under with a 4" flap disk and give it a slight edge, tractor works much less and cuts shit clean.
Takes 5 minutes. Like others have said pto shafts only go on one way, have to look at it close to see the different humps. |
|
Grammer Nazis be dammed!!
|
Going in part way and stopping sounds like a dent or bend to me. Got a drive line shop near by?
|
|
|
|
|
Well after a lot of online educating myself on PTO shafts I believe it's bent or tweaked in some way. It's the "Italian" style shaft. Supposedly needs to be straight as an arrow or it won't go together right. Going to try to contact a drive line shop and see if they can fix it. Otherwise a new complete assembly runs about $250 or so. Consider it a lesson learned. Thanks for the help!
|
|
|
If the pressure only nearly cut the plastic, I'd be surprised if the shaft actually got bent.
The ones I've used, and even the two I have are seriously hefty. The pto shaft for my chipper is a pain to put back together mostly because of the shield blocking easy eyesight and manipulation. Are you completely unable to slide them together? Or are they sticky after you get them slid together? |
|
|
Originally Posted By deerranger: I sharpen the blades on my brush hog a couple times a year, very easy to raise it up and crawl under with a 4" flap disk and give it a slight edge, tractor works much less and cuts shit clean. Takes 5 minutes. Like others have said pto shafts only go on one way, have to look at it close to see the different humps. View Quote @deerranger How do you support your mower. I want to sharpen mine but that kind of scares me. Thanks. |
|
17 And that no man might buy or sell, save he that had the mark, or the name of the beast, or the number of his name.
|
Originally Posted By Bronsonburner: Well after a lot of online educating myself on PTO shafts I believe it's bent or tweaked in some way. It's the "Italian" style shaft. Supposedly needs to be straight as an arrow or it won't go together right. Going to try to contact a drive line shop and see if they can fix it. Otherwise a new complete assembly runs about $250 or so. Consider it a lesson learned. Thanks for the help! View Quote Go to the place you bought it. I’ve done this several times. They can either repair or replace in about 30 minutes if not too busy. Take the entire shaft with you. |
|
17 And that no man might buy or sell, save he that had the mark, or the name of the beast, or the number of his name.
|
I put the bucket of the excavator under the mower, you really only have to go underneath by the tail wheel, only your arms are under the deck.
A log or some blocks will keep you safe. |
|
Grammer Nazis be dammed!!
|
Sharp blades make much cleaner cuts on grass & stringy stuff. Where I grew up there was an Amish blacksmith that would heat & hammer them for $40 a set. They last much longer when hammered to a fine edge vs sharpened with a grinder. And big blades would take a couple hours to sharpen with a grinder.
|
|
|
Originally Posted By Oldgold: Go to the place you bought it. I’ve done this several times. They can either repair or replace in about 30 minutes if not too busy. Take the entire shaft with you. View Quote I may do this Saturday. Place is an hour away though. If that fails I have seen the tubing available online for pretty cheap. I played around with it the other day and went as far as to knock the roll pin out of the fitting but I need to know how to knock the tubing out. Is a press of some sort needed? |
|
|
Sign up for the ARFCOM weekly newsletter and be entered to win a free ARFCOM membership. One new winner* is announced every week!
You will receive an email every Friday morning featuring the latest chatter from the hottest topics, breaking news surrounding legislation, as well as exclusive deals only available to ARFCOM email subscribers.
AR15.COM is the world's largest firearm community and is a gathering place for firearm enthusiasts of all types.
From hunters and military members, to competition shooters and general firearm enthusiasts, we welcome anyone who values and respects the way of the firearm.
Subscribe to our monthly Newsletter to receive firearm news, product discounts from your favorite Industry Partners, and more.
Copyright © 1996-2024 AR15.COM LLC. All Rights Reserved.
Any use of this content without express written consent is prohibited.
AR15.Com reserves the right to overwrite or replace any affiliate, commercial, or monetizable links, posted by users, with our own.