User Panel
Colt AR15 and Polish PMKMS Cool-Aid Is Good!
SD, USA
|
Wow. You've just made my life easier. Thanks.
|
> The M16 needs a gas piston like the AK needs to go without a gas piston. Knock it off. It is a fad!
> Installing Tapco tacti-coolio gadgets on an AK is like taping a PC memory stick on the outside of a typewriter. |
great write up! i know some people dont mess with them because they are not sure about it.....think this will help with that
|
|
|
thanks mods for making this a sticky.....i am sure it will help some other people out there
|
|
|
Great thread, thanks a lot. The only part of this that would worry me is drilling the hole through the piston nice and straight.
|
|
|
|
I was just wondering about this.
|
|
"We will always remember. We will always be proud. We will always be prepared so we may always be free." Ronald Reagan 1984
|
So, where do you get the rivet? I have done everything else. USA grip. USA trigger parts. Thanks, AC
Pic |
|
|
I wondered how the hell to get that apart.
Thank you |
|
Posted By 455SD: Newspaper, man. Newspaper.
Posted By Napoleon_Tanerite: meh... gives my garage floor that well used look. Posted By Johnny_Reno: That's true. It's very difficult to throw your garage floor down the driveway. |
What is the thread size in the carrier where the piston screws in ? I need to get a tap to chase my carrier.
Thanks |
|
|
Also wondering where to get the rivet. Thanks. |
||
|
|
This tutorial is pretty decent, but it's lacking a few subtle but (in my mind) important details. I would like to amend it with the following information:
First, to answer a previous question - the gas piston / carrier are threaded for 12mm x 1.25. You might want to run a tap into the carrier to ease the installation of the new piston (most likely, the carrier is slightly out-of-round from the original riveting process). Now on to the missing details.. it's worth noting that while the holes in the bolt carrier are ~0.120" (3mm) the hole through the gas piston is actually ~0.140" (3.5mm). This difference in size exists to assure that the piston is able to float (wiggle) when installed. And yes, the float is important - it helps to compensate for misalignments resulting from manufacturing tolerances. DO leave a gap between the piston and carrier as in the original installation - 1/2 turn back out from flush is fine. So - make your first drilling (through carrier & piston) with a 3mm (#31) drill. Then, remove the piston and enlarge the hole to 3.5mm (#27 or 9/64" drill). Pass a 1.25mm 'thread restorer' file (or a die) over the threads to remove any flash from the drilling. Now reinstall your piston and rivet / finish as above. Tip: Before enlarging the hole, use a #2 center drill (aka combined drill and countersink) to put a slight chamfer on both ends of the hole in the piston. This will reduce or eliminate the tendency of the #27 / 9/64" drill to catch and bind up as it enters and exits the hole. Enlarging a hole puts a lot of stress on the edges of the drill flutes; we want to keep the abuse to a minimum. Hope this is helpful. -L |
|
|
good points made in the last post - I'd like to add too that the size of the gap is important. The overall length of the bolt carrier and piston measured from the L side impact surface is important. the gap is 0.4mm max, with OAL 294mm min and 295 max. Max deflection is 5mm from ceneterline, but I've never seen one nearly that loose.
Maybe someone can check my math here 1.25 mm per revolution = .8mm in 360 = .4 mm in 180 degrees = .2mm in 90 degees. One problem is if the face of the bolt carrier isn't perfectly perpendicular than you can get different readings at different spots. I just use the OAL measurement and 294.5 usually equates to 1/8 turn. I did 1/4 turn before I got the gauge, which mathematically seems to put me in the middle of the .4mm max, but is longer than the 294.5 gauge midrange. Maybe its a function of the TAPCO piston length. |
|
|
Ive used a regular nail...Find one that fits the hole, cut it shorter...then peen over one side...then the other side. No need to buy a rivet when you probably have a box of nails just sitting there in your home.. |
|
|
Originally Posted By Fishpaw:
Ive used a regular nail...Find one that fits the hole, cut it shorter...then peen over one side...then the other side. No need to buy a rivet when you probably have a box of nails just sitting there in your home.. I just don't see how this works.. and I've tested it out at one point. Nails are made of hot-worked tempered wire, this is why they don't easily collapse (or mushroom all that much) when struck with a hammer. I tried to peen over several different nails (not in bolt carriers) and they easily resisted the levels of force that I'd be willing to apply.. especially when valuable parts are close by. On the other hand, the available rivets are easily beaten into shape with a series of light, well-placed blows. But the ones supplied by AKbuilder do need to be shortened quite a bit before setting. I do this in a minute on the bench grinder. -L |
|
|
Originally Posted By Gunplumber:
Maybe someone can check my math here 1.25 mm per revolution = .8mm in 360 = .4 mm in 180 degrees = .2mm in 90 degees. Maybe I'm misunderstanding, but a 1.25mm pitch advances by 1.25mm in one revolution. So, 360' = 1.25mm / 180' = 0.625mm / 90' = 0.3125mm Also, I'm unclear on what you meant by "max gap is 0.4mm". Is this the gap between the front of the carrier and the flange on the piston - i.e. the gap that is opened when the piston is backed out from flush? Interesting points on the OAL of the carrier / piston. Are the 294/295 figures from a blueprint, or did you derive them in the course of your own work? I've always done the 1/2 turn out and pin, and haven't ever detected any functional issues. But I'm going to begin checking this dimension, now that you've mentioned it. Then of course, the position of the gas block also comes into play.. -L |
|
|
Awesome thread. This should be tacked.
|
|
|
AC12, et al,
I have about 60 rivets left if anyone needs them. I bought a box of 100 1/8" x 3/4" stainless steel countersunk solid rivets from McMaster-Carr, because I was having problem searching the AK sites for them. (Why they don't have optional "mechanically inclined buyer" piston kits that include the rivet, I'll never know?!?!) I did my piston and had 99 left. I gave a bunch to my local FFL, who helps me out quite a bit. The rest are just sitting here awaiting use. If you need one e-mail or IM me. Price: Free to a good home!!! Just remember me if you have any good parts kit deals, and maybe give me first right of refusal. Bigun |
|
|
Originally Posted By 2ndAmendican:
(...) I bought a box of 100 1/8" x 3/4" stainless steel countersunk solid rivets from McMaster-Carr, because I was having problem searching the AK sites for them. (Why they don't have optional "mechanically inclined buyer" piston kits that include the rivet, I'll never know?!?!) (...) Curtis at AK-builder.com includes a rivet with the purchase of a gas piston. Loose rivets were $1.25/ea last time I checked, but he tends to give price breaks on rivets to owners of an AK-builder rivet press. -L |
|
|
Just put a U.S. piston on my carrier and it was easier than I thought. I tried to get the gap to look the same as the original, but I'm not sure how accurate it was. I need to take it to the range to ensure smooth operation. Thanks for the write up!
|
|
|
I just used this to change the piston in my MAK90. I just measured the OAL of the entire carrier and threaded the new piston in to match the old length. The TAPCO piston was pretty hard to drill through, but the results were great! Took the MAK out and gave it a torture test today and it worked flawlessly.
Thanks! |
|
Instructor: Sniper, Patrol Rifle, Handgun, Shotgun - Armorer: Glock, Colt AR15/M16
|
Sign up for the ARFCOM weekly newsletter and be entered to win a free ARFCOM membership. One new winner* is announced every week!
You will receive an email every Friday morning featuring the latest chatter from the hottest topics, breaking news surrounding legislation, as well as exclusive deals only available to ARFCOM email subscribers.
AR15.COM is the world's largest firearm community and is a gathering place for firearm enthusiasts of all types.
From hunters and military members, to competition shooters and general firearm enthusiasts, we welcome anyone who values and respects the way of the firearm.
Subscribe to our monthly Newsletter to receive firearm news, product discounts from your favorite Industry Partners, and more.
Copyright © 1996-2024 AR15.COM LLC. All Rights Reserved.
Any use of this content without express written consent is prohibited.
AR15.Com reserves the right to overwrite or replace any affiliate, commercial, or monetizable links, posted by users, with our own.