update, 1/15/2024, NO LONGER AVAILABLE from instructions below. This direct link is still working for now.

 
https://cdn.ar15repository.com/wp-content/uploads/20230713193439/ff-0d1fa9f7d40bcb9b459c03695c5e6629-ff-COLT-CM118-Defense-Operation-Maintenance-Manual-2010.pdf





Here is the direction to download the Colt 3 Day School CM118 Armorers Manual.

This CM118 manual is far superior to the many military 23&P Manuals you can find everywhere. Who knows how long it will be up. Download while you can.

Thanks for sharing will try later

Good stuff there

Excellent post !  Appreciate the share .

Also that site is new to me and looks like there is some good info .

Thanks for the info !..A great manual for clear and concise info on Colt Ar’s

I have no idea who owns it, .  But yeah lots of good info.

Any other way to access
ETA:
Done in an alternative way

Just checked, still works for me, might try a different browser? OK, or maybe you got in after all?

Thanks OP, nice addition to my library

Got it... Thanks!

Yup
Using Google Translate I was able to get around the IP block.
I guess they don’t like users OCONUS

Attached File

Well, that was worth a look. I might have to print that off even if for no other reason than the torque specs and tightening procedure for the 6940 barrel nut.

Thanks OTDR!


I did see some odd torque specs given for RIFLE receiver extensions/buffer tubes and very wrong installation procedure for the crush washers. Also, (as has been noted before) Colt's listed torque spec for the pistol grip screw is insanely high at "60 - 65 inch pounds". Whoever wrote that must have been drunk... No more than 30 - 35 inch pounds and 35 is pushing it considering the polymer of the grip.

Thanks!

Here's the direct link: https://cdn.ar15repository.com/wp-content/uploads/20230713193439/ff-0d1fa9f7d40bcb9b459c03695c5e6629-ff-COLT-CM118-Defense-Operation-Maintenance-Manual-2010.pdf

Thanks had not seen that one.

Added to my Google Docs.  Great post OP!

Thanks for that info.

Thank you.

Got it, thanks OP.

Oh, thank you to the OP and to the dude who posted the direct link.  Thank you, both!

Downloaded it thanks.

A subscriber to my Youtube Channel left this comment about the Colt Armorers School:

-------------------------------

So, I just finished the class yesterday. First and foremost I would like to say that there is no stress. There was an exam at the end and a few practices, however it was not so bad. No one failed. 2nd, this course is valid every 3 years so I was in a class with other students that were much more knowledgeable then I was. This meant I was left behind. However, the instructor and students helped me out when needed. On to the course….

The first day was a lot of “ Sea Stories” (well police stories anyway) that pertained to the AR. We did some introductions and took a pretest. We went over the history of the gun (briefly) the different models that came before and the current models. The first half of the day was just talking and teaching. After an hour lunch, we came back and grabbed the rifles and took kits (all provided by the Colt to use, not given). We broke down the bolt assembly all the way down with exception of the staked portion. Then, we put it back together, then again and again. We finished the day off around 3pm (started at 8). Being in the military, I was pretty familiar with the bolt carrier group, I can break that down and throw it back together in no time. I felt pretty confident going into the second day. That did’t last long.

Day 2 was the lower receiver, I have never touched that before, I always figured with was some kind of fairy magic and I don’t have to worry about it. Seems that isn’t the case. You start with the hammer then trigger assembly then on and on and on, I was taking out the pivot and takedown pins, the mag release, bolt release, pistol grip, I had springs galore. I got lost real quick. Putting this this back together was not a walk in the park. You literally have to do it at least 10 times before you can get a handle on it. But, we would go over a section and do it multiple times. Go over another section and do it multiple times. Before I knew it, I had a pile of time parts and time springs everywhere. However, we did it enough so I would know what is what. It was actually pretty freaking awesome.

Day 3 was the upper receiver, barrel removal, practical, and exam. There are not as many springs but definitely takes time to learn how to manipulate the parts of the upper receiver. The day starts off by taking everything apart then switching seats with someone to put their gun back together. You learn by repetition, the more I did the better I got. After lunch we took the barrel off, did the practicals where the instructor created a malfunction int he weapon and we had to find it. Then we went over the maintenance of the AR / M4 and did a test review. Then we took the test (like 20 questions) and course evaluation. Fin.

The test I think is a formality. But, when you see a pile of parts on a table and you can identify where each goes and how to put that weapon back together, that’s where the real gratification comes in. The course itself is great. I took the law enforcement version so your class may be different. All in all the course is well worth it.

that page is a treasure. lots of downloading to do.

BUMP, update in the OP.

The hotlink by KitBuilder (post #13 here) is a viable direct link.

I put that link in the OP when I bumped the thread. Thats what I did.

Your hot linking skills are lacking.  

Very cool. Thanks, op. I love to nerd out on user manuals. I’m that guy who reads them cover to cover before using the tool.

Fixed! Happy now?

Not sure whats happened to the site, investigating as there are a lot more to look at there. Should be back up soon.

Cool, thanks for sharing.

Just busting your balls some.

I would appreciate it if you kept you filthy grimy hands off my balls

Are there any other discrepancies that guys like me that are starting to do more involved work on their rifles should be aware of?

@OTDR
@556Cliff

Save to my phone files so I can print later.

Just got this sucker bound at Fed Ex:

Attached File


Attached File


I don’t have a color laser jet printer, so black and white had to do.

For once, "juS as gUd" actually applies!

@556Cliff

Haven't seen cliff around in a while and he isn't taking IM either, please dear Gawd let Cliff be OK.

Yeah, color would have been nice.

Many thanks to a generous member here....

Attached File

Your a blessed man!

Fortunate, for sure.

I didn't notice any other discrepancies when I last looked through the manual. If I happen to look through it all again and notice anything I'll make sure to post it here.

Still alive, was just taking an ARFCOM (and social media in general) break.

That stupid ban has taken the wind out of my sails a bit too.

Where you been my friend? Haven't seen you around, was about to send out an alert. Your not taking IMs either.

Bunch of the last green Hulks came thru discounted due to being blems lol!

The Colt manual available for download on this page is 2010 version.

I saw a few posts up where TIG was gifted a real 2014 version, Im Jealous and I bet i can guess where he got it.

But there is no differences in them except for some grammar.

Thanks

Ha! No need to sound the alarms, I was just taking a break from here and other social media. Figured it would be better to have my IMs off while I wasn't checking in here.

I have been watching the green jigs though, I was surprised they had that many blems in the anodizing on that last batch... As hard as it is to resist, I still haven't ordered a second one.

Those ejector cut headspace gauges from Forster have got my interest and I'll probably be ordering a set of those on my next Brownells order.

They work really good.

That's what I like to hear.

It's another one of those things where I'm surprised it took so long for them to come out because it's always seemed like there's been a demand for them.

Colt Canada Operators Manual

https://www.coltcanada.com/wp-content/uploads/2021/04/10044s-2005-09-20.pdf