User Panel
Posted: 10/26/2023 8:40:51 PM EDT
[Last Edit: TontoGoldstein]
Update in last post from me.
OP: Both are .45 octagonal barrel muzzle loaders in what I would call carbine length. Cap and ball, not flintlock. Because they were owned by a meth head, the bores weren’t cleaned and have pitting. I’ve been scrubbing them with bronze brushes. After I got the easy stuff out, I assembled a 9 volt cleaner and got a great deal more out. Brushed some more and then plugged the nipple and filled them with PB Blaster. I let them sit overnight, poured out even more sludge. I would like to remove the breech plugs, but I don’t have the knowledge or equipment to attempt such. The small screws filling the clean out holes under the nipples are frozen. At this point I am unsure how much farther to go. Do I clean as well as I can, shoot it, and then clean it well or should I find someone to remove the screws and also remove the breech plugs. Any advice is welcome. Stock representative photo. Attached File |
|
"Nothing in life is so exhilarating as to be shot at without result." - Winston Churchill
|
[Last Edit: AeroE]
[#1]
Take the barrels out of the stocks and show us photos of the breech end from different aspects. The breech plug could be simple. If it's a patent breech, probably not if there is a pin.
Don't worry too much about the breech plugs. If they are fit correctly, there's not much going on inside. The screws need a soak in pentrating oil, a screwdriver that fits correctly, and possibly a hammer powered impact driver (motorcycle style) if they resist. That gun was sold as a "Hawken" replica; it ain't, but that doesn't it shouldn't be shot and used. The brand should be on the barrel. Investarm used that patch box |
|
Keep your powder dry, and watch your back trail.
|
[#2]
Attached File
Attached File Attached File Attached File The brownish one is a Thompson Center. The bore is extremely rough even after soaking, scrubbing, and electrolysis. I have tried to remove the breech block with zero success. It is the one with the protruding clean out screw. I am thinking that relining it is my only option. The other is a Cabela’s. Its bore may be salvageable. I have not tried to remove the plug yet. Any input on this is greatly appreciated. |
|
"Nothing in life is so exhilarating as to be shot at without result." - Winston Churchill
|
[Last Edit: kychas]
[#3]
Plug the nipple and fill the barrel up with vinegar and lit it sit for a day or two
Or this https://www.amazon.com/Henkel-NAVAL-JELLY-Fluid-Ounce/dp/B000C016OC Be careful with the naval jelly. It will strip the browning or blueing off the outside of the barrel Wash and scrub out and inspect I normally wash my muzzle loaders with hot soapy water and a tight patch. I put a rubber hose on the nipple and the in and out movement will push out the air and pull in water and then pushes out / in water until it is clean. Keep a towel around the top to catch water that gets on top of the patch Dump and drain and put up and it will steam dry I have an old cva Ky long rifle from 1978 or so It is pitted and still a tack driver You just have to clean and try it and see how they act Remember to figure out the twist rate so you know to use lead ball or maxi ball to test for accuracy |
|
|
[#4]
Some of the old Thompsons had Douglas barrels. I have one. Dont let the rusty barrels discourage you. They can most likely be scrubbed out and be good shooters.
|
|
|
[#5]
After you clean them as much as you can, get some JB bore paste and use a black powder Jag with a patch soaked in the paste.
Just keep scrubbing with it you may notice the patches tearing from the rough pitting, keep going until the patches no longer tear. It will smooth up the lands and groves, not perfectly but it will be to an acceptable level. |
|
|
[#6]
The TC patent breech plug is too difficult to remove and there is no real need. You'll find a pin.
I would remove the clean out screws, replace, and shoot the guns. Relining isn't worth the trouble, if you can find a liner. Buy a barrel on GunBroker if you are determined. |
|
Keep your powder dry, and watch your back trail.
|
[#7]
I've seen and fixed worse, once you've cleaned them as good as it gets, it's time to go shoot them.
They aren't going to be target rifles suitable for competition without significant work. I would probably start with a good cast hollowbase bullet with a bunch of lube to help shake loose the crud and also make cleaning easier. |
|
|
[#8]
I'm not able to get the nipples off. I don't want to snap them off. Should I heat that area with a propane torch?
|
|
"Nothing in life is so exhilarating as to be shot at without result." - Winston Churchill
|
[Last Edit: firemedic5586]
[#9]
Originally Posted By TontoGoldstein: I'm not able to get the nipples off. I don't want to snap them off. Should I heat that area with a propane torch? View Quote I have no idea one way or another regarding heating the barrel that much.. I'm leaning more towards maybe not. That said, one of THESE will give you more control then a torch. |
|
There comes a time when you look into the mirror and realize that what you see is all that you will ever be. Then you accept it, kill yourself, or you stop looking into mirrors.
|
[Last Edit: JupiterMaximus]
[#10]
Originally Posted By TontoGoldstein: I'm not able to get the nipples off. I don't want to snap them off. Should I heat that area with a propane torch? View Quote Heat away. Propane torch alone won’t get it hot enough to weaken it for BP use. It usually doesn’t take a lot of heat to get stuck metal parts to move. Heat the area around the nipple, not the nipple so much. |
|
|
[#11]
Several times i've had nipples that were stuck. Trick i have successfully used is getting a soldering iron, and heat up the nipple itself. Then take a can of computer air, turn it upside down, and blast the very cold air right though the middle of the nipple. Make sure you do not stick the tube too far in and get the cold on the nipple itself instead of too deep. Sometimes you will hear a pop when the cold hits the hot metal. Very quickly get your nipple wrench on the nipple and it usually will come loose then. As far as a rough bore, you are not dealing with very high pressure with black powder. i've had several very pitted bores that shot acceptable groups in spite of pitting, but it does make cleanup harder when there are a ton of pits. JB Bore Paste will help some as will some other grind compound type solutions. i even firelapped a few BP barrels over the years with success in smoothing out the pitted barrels.
|
|
|
[Last Edit: mechanicuss]
[#12]
Originally Posted By Tango:...Dont let the rusty barrels discourage you. They can most likely be scrubbed out and be good shooters. View Quote Agree. If it will load a lubed tight patched ball without tearing the patch or causing a stuck ball, and it shoots into the bullseye at 50 yds, then it's really just cosmetic - am I not right? Just don't look at it. Liver Eatin' Johnson didn't have a borescope LOL. But, I hear you, I obsess over bore cleaning myself - you can do that if you buy new because you can keep it clean and not let it get that way. If it's too rough take a smaller sized jag and cut a piece of maroon Scotch-brite as a patch and smooth over the rough edges of the pits until you can run a patch in and out without it tearing or catching real bad. Here's a video of Mike Beliveau doing it: Polishing a rough bore After you shoot it a lot over time the pits will sorta fill in with baked on black graphite-like carbon which seems harder than the steel itself lol. Shoot the heck out of it and have fun. @TontoGoldstein |
|
|
[Last Edit: TontoGoldstein]
[#13]
One rifle is a Cabela’s .45 Hawken style with very strong rifling. It is an attractive rifle. It had the least rust. After many brushings, I filled the barrel with Evapo Rust. Even after days of cleaning I was amazed at the amount of crud that poured out. I suspect that the breech plug was pretty bad.
After Evapo Rust, I put the barrel breech block first into a bucket of new paint thinner. Using a swab I pumped a bunch of the thinner in and out. Even more sludge. Liquid easily flows out of the nipple hole. I decided to stop at this point. I swabbed the bore with 30W synthetic and set it aside. When it comes time to shoot it, I will rinse the bore with isopropyl alcohol to get it clean and dry….and then get to it. The next was a Thompson Center .45 Hawken style. This one showed no rifling. I cleaned and cleaned and decided to throw in the towel. Unable to find a reasonable replacement barrel, I looked at electro chemical rifling, turning it into a .50 or a smooth bore looked like more money and work than worth it. I had the breech plug removed mechanically without heating and got to cleaning it again. Long story short, it has shallow rifling common to TC rifles. There is still pitting and I would never buy a rifle in this condition. Time will tell. My biggest concern will be cleaning black power out of the pits after firing so that the corrosion doesn’t start again. Like the Cabela rifle, I reassembled it and will give it a shot later. It isn’t nearly as pretty as the Cabela one. Frankly it’s been a blast. I love fixing stuff. |
|
"Nothing in life is so exhilarating as to be shot at without result." - Winston Churchill
|
[#14]
Waiting.
Test fire the rough bore. It may still shoot accurately. |
|
#53 says, "Take 22 mg absorbed Vit C per lb plus 1 gram Chaga daily. Don't forget 2000iu Vit D-3 & K-2, 30 mg Zinc and 2 mg Cu."
Unfettered with the formalities of an economics education but well read in monetary history. |
[#15]
Originally Posted By Cantshootstrate: I've seen and fixed worse, once you've cleaned them as good as it gets, it's time to go shoot them. They aren't going to be target rifles suitable for competition without significant work. I would probably start with a good cast hollowbase bullet with a bunch of lube to help shake loose the crud and also make cleaning easier. View Quote @Cantshootstrate Would you please tell me what cast hollow base and where I can get them? I’ve been reading Fadala’s Black Powder Loading Manual put out by Gun Digest Years ago. I’ve been shooting main battle cartridge rifles for decades. But I know next to nothing about BO rifles. |
|
"Nothing in life is so exhilarating as to be shot at without result." - Winston Churchill
|
[Last Edit: mechanicuss]
[#16]
On second thought, maybe smearing lead into those pits and filling them up with lead ain't such a bad idea lol. Sorta like muzzleloader Bondo lol. Might make it easier to load patched balls! |
|
|
[#17]
Give this guy a call to have the barrels rebored larger. If you want.
Bobby Hoyt Freischutz Shop 2379 Mt Hope Rd Fairfield, PA 17320 ph# 717-642-6696 |
|
|
[#19]
Have an original 1842 musket barrel with rust around the nipple. Took a Monster Drink can, cut the top out, placed the breech end in it, and then filled with Kroil oil to cover it. Then poured Kroil oil down the bore. Set on the corner of the work bench for about a month. Every week would run a cleaning rod and in it a couple of times. In the end, the nipple easily came out with normal torque with a nipple wrench.
May be more time than you want but may be the easiest way to get those stuck screws out. |
|
Call the tune and let's dance; but beware that the devil is the piper and the tab for that soiree will be hell to pay.
Training&Trigger Time are more important than chasing a hardware Holy Grail |
[#20]
Thanks to all the responders.
|
|
"Nothing in life is so exhilarating as to be shot at without result." - Winston Churchill
|
Sign up for the ARFCOM weekly newsletter and be entered to win a free ARFCOM membership. One new winner* is announced every week!
You will receive an email every Friday morning featuring the latest chatter from the hottest topics, breaking news surrounding legislation, as well as exclusive deals only available to ARFCOM email subscribers.
AR15.COM is the world's largest firearm community and is a gathering place for firearm enthusiasts of all types.
From hunters and military members, to competition shooters and general firearm enthusiasts, we welcome anyone who values and respects the way of the firearm.
Subscribe to our monthly Newsletter to receive firearm news, product discounts from your favorite Industry Partners, and more.
Copyright © 1996-2024 AR15.COM LLC. All Rights Reserved.
Any use of this content without express written consent is prohibited.
AR15.Com reserves the right to overwrite or replace any affiliate, commercial, or monetizable links, posted by users, with our own.