Warning

 

Close
Confirm Action

Are you sure you wish to do this?

Cancel Confirm
AR15.COM
7/23/2018 6:44:40 PM EDT


Test Gun: Delta Elite
Barrel length: 5 inches.
Bullet: Hornady .400 200gr XTP (Handload).
Test media: 10% Clear Ballistics Gel.
Distance: 10 feet.
Chronograph: PACT 1 XP with inferred sky screens.
Five shot velocity average: 1159fps
Gel Temperature 71 degrees.

I have always liked the XTP bullet even though it seems to be overshadowed by some of the more premium bullets available. It seems to normally give modest expansion with deep penetration and I felt it would make a good choice in the 10mm. I worked up a load using Alliant Blue Dot and ended up with a five shot average of 1159fps with a high of 1180fps and a low of 1134fps. 46fps spread is a little more than I would like to see. There was no sign of excessive pressure and I may bump up the charge and see if that brings down the extreme spread. Other than that I’m pretty happy with this load.



The first shot into the bare gel penetrated 19 inches and expanded to .64 inches. The second round went 21 inches and expanded to .65 inches. Unfortunately, the chronograph didn’t pick up either shot.



I then shot two rounds into the heavy clothed gel with the first round penetrated 25.5 inches at a velocity of 1195fps and expanded to .53 inches. Round two hit at 1162fps, expanded to .52 inches and penetrated to 22.5 inches.



Later in the day, I decided to shoot the last round I had through four layers of heavy denim. Unfortunately, the bullet exited the left side of the second block and the 23-inch mark and was found lying on the floor. As you can see the denim retarded expansion considerably.



http://www.general-cartridge.com/
www.general-cartridge.com
7/23/2018 6:52:22 PM EDT
[#1]
Interesting.
"They who can give up essential liberty to obtain a little temporary safety, deserve neither liberty nor safety."
Ben Franklin
7/24/2018 11:53:55 PM EDT
[#2]
Good old Blue Dot.  They should just rename it 10mm Dot and be done with it.

I'd be interested to know how many grains of powder?  If you don't feel comfortable posting that publicly shoot me a PM.
7/25/2018 6:30:22 AM EDT
[#3]
Quote History
Originally Posted By NVGdude:
Good old Blue Dot.  They should just rename it 10mm Dot and be done with it.

I'd be interested to know how many grains of powder?  If you don't feel comfortable posting that publicly shoot me a PM.
View Quote
9.4 grains, CCI200 primers.
www.general-cartridge.com
7/25/2018 7:43:45 AM EDT
[#4]
Quote History
Originally Posted By NVGdude:
Good old Blue Dot.  They should just rename it 10mm Dot and be done with it.

I'd be interested to know how many grains of powder?  If you don't feel comfortable posting that publicly shoot me a PM.
View Quote
Works great in .40 S&W and 9MM, too.

Mine is old shotgun powder reloading stuff from my dad's stash of powders.
How you live your life is important. Just be sure the memory of how you died doesn't overshadow the tales of how you lived your life.
7/26/2018 7:47:52 PM EDT
[#5]
I had the chance to try some Nosler 200gr JHP today. I used the same 9.4gr of Blue Dot I used with the XTP. The average five-shot velocity was about 20fps less than the XTP at 1139fps with a high of 1163fps and a low of 1124fps. Even though the velocity was lower it seemed to have more recoil and muzzle flash. It also showed signs of higher pressure.

This time I just shot two rounds in bare gel and didn’t set up the chrony. The first round penetrated 19 inches expanded to .70 inches and had a recovered weight of 183gr. The second round only penetrated to 16.5 inches and a recovered diameter of .68 inches and a weight of 181gr.

It was interesting to see how the Nosler performed but I think I’m going to continue forward with the XTP.

www.general-cartridge.com
7/29/2018 8:23:12 AM EDT
[#6]
Quote History
Originally Posted By 5pins:
9.4 grains, CCI200 primers.
View Quote View All Quotes
View All Quotes
Quote History
Originally Posted By 5pins:
Originally Posted By NVGdude:
Good old Blue Dot.  They should just rename it 10mm Dot and be done with it.

I'd be interested to know how many grains of powder?  If you don't feel comfortable posting that publicly shoot me a PM.
9.4 grains, CCI200 primers.
I use CCI magnum primers with my 10mm loads. Have you ever tried them with Blue Dot and the 200gn Hornadys?
7/29/2018 8:26:22 AM EDT
[#7]
Quote History
Originally Posted By Nick_Adams:

I use CCI magnum primers with my 10mm loads. Have you ever tried them with Blue Dot and the 200gn Hornadys?
View Quote
No, I have not.
www.general-cartridge.com

Sign up to continue the discussion

Create a free account to share your thoughts, follow topics, and connect with the AR15.COM community.

Already a member? Sign In