Warning

 

Close
Confirm Action

Are you sure you wish to do this?

Cancel Confirm
6915 Online
bravocompany bravocompany bravocompany
brownells brownells
tnvc tnvc tnvc
AR15.COM
bravocompany
My Account
bravocompany bravocompany bravocompany
brownells brownells
tnvc tnvc tnvc
midwest
JRH
magpul
cz
vortex
RS
skd
brownells
geissele
palmetto
DFC
primaryArms
bravocompany
GS
Guns
OSIGHT
Holosun
aim
springfield
silencerShop
colt
fightlite
6915 Online
aim
palmetto
GS
RS
JRH
primaryArms
brownells
Holosun
Guns
bravocompany
vortex
fightlite
silencerShop
geissele
skd
DFC
midwest
OSIGHT
magpul
colt
cz
springfield
AK Sponsor
Sponsor News Introducing TNVC's NEW and Exclusive Filmed SuperGain (FSG) and Chimera Panoramic Goggle Giveaway!
Site News The People of Virginia VS Grabigial BanBerger | ARFCOM News
8/17/2006 4:43:50 PM EDT
Before I start, I will admit I did ask this question before but because I am not ::coughshortbuscough:: special , by the time I got around to fixing it (I will also admit it took awhile) the thread was gone and I cannot reference that far back.  Sssoooo...
The axis that holds the trigger assembly upright by means of the two holes in the receiver just above the trigger keeps falling out of place after a couple squeezes of the trigger.  Does anybody have any idea what part is AWOL and where I can get another?
8/17/2006 5:10:06 PM EDT
[#1]
Tapco, K-VAR, DPHarms.com should all have the part.  Shepard's hook or crook or RSA replacement.




WASR trigger assembly will not stay in    

BeAsT762
Member
Joined :: September 2005
Post Number :: 23

VA, USA

OK, I can't post pictures so I will try to use my amazing knowledge of English (  ) to describe it. There is a little pin right above the trigger that holds the entire thing in place. When I pull the trigger two or three times, the pin falls out of it's hole on the ejection port side. I then have to play with it on the other side of the weapon to push it back into the hole. If I push and hold the pin from the non- ejection port side, I can pull the trigger as much as I please without a problem. Any possible solutions? I was thinking of getting permafix or something and applying it to the OUTSIDE of the weapon on the to sides of the pin, holding it in place. Does this sound like a bad idea?
Thank you!!!



--------------------------------------------------------------------------------
Posted :: 5/16/2006 12:06:19 PM
Last Edited :: 5/16/2006 12:08:43 PM by BeAsT762




legonas
Team Member
Ubergeek AK lover
Joined :: March 2002
Post Number :: 1310

SC, USA

the trigger retaining wire is missing / not installed correctly.

www.gunsnet.net/Linx310/fcgremoval.htm for more info

here is a drop in easier to use replacement; www.tapco.com/product_information.asp?number=AK0680&back=yes&dept=190&last=13


--------------------------------------------------------------------------------
"The universe is an infinitely faceted diamond, and each of our souls is reflected in its magnificence. Choose your facet, your window to the world, wisely."


--------------------------------------------------------------------------------
Posted :: 5/16/2006 12:22:04 PM
Last Edited :: 5/16/2006 12:23:38 PM by legonas




stargazer111
Member
Joined :: January 2006
Post Number :: 193

TX, USA

Make sure both pins of the trigger assy. go "in" on the left side of the receiver.



--------------------------------------------------------------------------------
Posted :: 5/16/2006 4:21:36 PM




BeAsT762
Member
Joined :: September 2005
Post Number :: 24

VA, USA

Great, thanks a lot!



--------------------------------------------------------------------------------
Posted :: 5/17/2006 11:42:38 AM



WASR trigger assembly will not stay in  
AK Sponsor
Pro2A
geissele
SAS
ar15com
springfield
palmetto
RS
Faxxon
brownells
ar15com
gray
ar15com
blackhills
LAPG
silencerShop
primaryArms
bravocompany
LAPG
colt
CA
cmmg
fightlite