Warning

 

Close
Confirm Action

Are you sure you wish to do this?

Cancel Confirm
AR15.COM
Armory Sponsor
9/14/2002 12:45:39 PM EDT
When you look through a red dot scope, do you have to use the red dot lined up with the front sight post, or is there a way to sight through a red dot scope without using the front sight post?
Thanks,
Ed
9/14/2002 12:48:23 PM EDT
[#1]
Red dots work independent of the iron sites.  Adjust it so that the bullet impacts in the center of the red dot.  Most dots are about 4 to 8 minutes of angle so all you should have to do is put the dot on the target and the bullet should hit it.  Don't put the dot under the target the way you do with irons.  
I think you will find that the are the fastest way to engage targets.
9/14/2002 1:07:50 PM EDT
[#2]
I guess its just that all the scopes I have ever used have a cross hair that from any angle you look, the bullet will impact there, where the cross meets. With a red dot, how do you make the red dot stay in the middle?
Thanks,
Ed
9/14/2002 1:10:33 PM EDT
[#3]
Same thing goes for a red dot.  no matter where you look at if from the bullet will impact where the dot is.  Once the scope is mounted point the rifle on a target, keep it there and move your head around.  You'll find that the dot moves around relative to the scope, but stays on the target.  It's kinda weird, but you get used to it.
9/14/2002 1:11:45 PM EDT
[#4]
Thanks a million, I thought I was crazy.
Ed
9/14/2002 1:52:41 PM EDT
[#5]
This depends on the scope.  My Tasco Accudot moves on the target a lot as the dot moves around the reticle.  It is best to zero the scope with the dot in the center of the lens, and always try to keep the dot near the center when aiming.


Quoted:
You'll find that the dot moves around relative to the scope, but stays on the target.

9/14/2002 1:55:58 PM EDT
[#6]
Another point when using a (non-magnified) red dot scope.... keep both eyes open. By doing that you end up with a red dot out in your field of view and can see other objects/targets around you. It's very fast once you get used to it.
9/14/2002 8:27:49 PM EDT
[#7]
to rehash whats been said...

(in ref to an Aimpoint, which is what I have (CompM))

The red dot should "sit" on top of the front sight post.

operation of the Aimpoint is independant of the iron sights. (use one or the other)

When sighting in the Aimpoint, it is very important to use the sighting technique you will employ in "the field".  For example, as suggested and what I would also recommend is to sight using both eyes open.  this gives you greater field of view and is easier to scan for 'targets'.  If you don't use the same technique, your point of impact will be different.


I suggest you read the manual on the Armys CCO (Close Combat Optic) Sight (Aimpoint)

M68 CCO Manual

happy shooting
9/14/2002 8:35:09 PM EDT
[#8]
fizassist

That's one difference between Tasco & Aimpoint.  There's no parallax in the Aimpoint.  No matter where the dot is, if it's on your target and you don't flinch, you'll hit it.

Another difference?   PRICE

I've got 4 Aimpoints & wouldn't trade 'em for a box of Tascos even if I had a box of rifles.
9/14/2002 8:48:30 PM EDT
[#9]
According to the U.S. Army's M-68 manual(generously provided by 7IDL), the Aimpoint is only parallax free OVER 150 yards.  Under that, the dot should be centered for accurate aiming.
Armory Sponsor