Armory Sponsor
Posted: 4/8/2003 6:55:24 PM EDT
|
I'm new to FALs (my first is inbound from a seller on this board) and I see a number of different Mags offered. Any opinions as to the "preferred" mag? I seen new in wrapper Steyrs at $21-14 each, Aluminum, and all manner of used from $4.00-14. Any recommendations on number to have on hand and preferred manufacturer or country of origin? My initial thought is that 20 mags should be more than adequate, but if in your experience there is a design weakness or some other factor to influence your recommendation (such as future scarcity), please let me know. Thanks very much, Brad |
|
I've tried new Austrian and Belgium mags, as well as some pretty rough ones from Tapco. All have fed and fired perfectly. I prefer the look of the G1 mags from Belgium and some people like the witness holes in the Steyr mags. I really don't think it matters. If you want cheap but fairly good condition mags, look up Vorbec. I bought my new ones from him but I understand he has about the best condition used mags around and they are cheap. |
|
To refinish mags, just thoroughly clean and de-grease them, and paint with Brownell's Aluma-Hyde II paint. Let the mag dry for about a week. That's right, a week. The paint is incredibly tough. If you're careful, the inside of the mag can be coated as well, leaving a mag that's highly resistant to the elements. While you're buying mags, don't forget the nifty speed-loaders for them, and 5-rd stripper clips, and bandoliers.. For mag pouches, use USGI 30-rd AR pouches. Cut out the dividers, and cut out some foam spacers from a GI sleeping pad for the bottom, 2 per pouch. Don't forget to punch a drain hole in the foam spacers. A stripper clip guide can be strapped into the grenade pocket on the side. Works great, and is cheep. |
|
When I got my FAL (DSA StG-58), I found some NIW mags from Tapco and Impactguns. Between the two companies I picked up 30 NIW steel mags for less than $280. I didn't know what was good and what to avoid in the used mags. So, I figured the NIW was the best way for me to go. I wouldn't worry about future scarcity on FAL mags. There are millions of these mags floating around. The only advice I can give you is maybe to stick with steel. From my reading, they seem to be recommended over others. Also, spend a little time at falfiles for their advice. raf has good advice on the stripper clips and guides. You might want to pick some up. |
|
The best "true FAL" pouches are the Camadian C-1 issue pouches. They were actually designed for the FAL andwork quite nicely. However, standard M-16 30rnd pouches work surprisingly well with the internal dividers removed! I didn't believe it and bought a bunch of the C-1 pouches.....then afterwords, I found an old M-16 pouch in my "stash", sans deviders. Put two FAL mags in....."Suna ma bitch!" They fit great! |
|
I have NIW FN Belgian mags, DSA "Good" grade Steyr mags, gun show "U pick-em" grade Steyr mags, some aluminum mags, and a 10 round DSA benchrest mag. Of all of them, the 10 round mag sees the most use. The NIW ones are just too nice to unwrap and use when the used ones are so readily available and work so well. The aluminum ones work fine and it's easy to feel the weight difference in loaded mags. I can't say how well they'll hold up over time compared to steel. The lip on the front that engages the mag release is the part I'd worry about. The DSA used mags have been the most consistently good quality ones for me. All the used ones needed a good cleaning to remove cosmoline, grease, sand, gunk, etc. DSA sells 20 round mag springs for $1.00/ea in quantity. These go a long way toward making the used mags work like new ones. That reminds me - need to stock up on some more while the getting is good. Mag pouches are tougher to come by. Tapco used to sell good quality 2 mag South African canvas pouches but I don't think they have them anymore. I haven't tried the other suggestions offered on this thread. Welcome to the FAL fraternity! 
|
|
I am also new to FALs and I want to buy a few mags for a metric FAL... I am curious if anybody has an oppinion on the 30rd mags... I am trying to look at the web as I would like to get 10-20 cheap mags to put away with a pair of parts kits that I have on the way... I figure a few mags put away now is good cheap insurance as opposed to what I have paid in the past for mags for my AR-10! I hear one recommendation for Tapco... anybody else know of a good place with good prices for servicable used mags...? Oh yea, I will buy a couple new Show-And-Tell mags but I need to start somewhere! QB |
 Hell, I know I don't actually carry many 20-rd AR-10 mags to the range for this reason (and I can't afford to refill them if I empty them)! Just the same, I have a pair of Imbel parts kits on the way from Dans and I really do need to grab a few Fal mags but I still haven't found a deal that has made me want to spend my money! It doesn't help that I have gotten the AK bug at the same time and I have been stocking up on AK parts, mags, as well as a new SAR 1... Yup... I am an official gun addict now! Hell, it's got so bad I have to make a list on paper to remember what guns I have and I could NEVER list the mags! |
|
I have got to the place where I take empty 20 round FAL mags, and a battlepack just for weight and logistics. The 308 is easier to load for my hands than the 223, so it only takes a few minutes, and I have tons of ammo to shoot. Damn last weekend with my FAL was like a first date all over again. I am truly in love with my FAL! (and 20 round mags are cheaper than a McDonalds Happy Meal date!) |
|
i recently bought a few of the "painted" fal mags from tapco. i couldn't be happier, only one out of six actually had a large amount of paint on it and they are fucntionaly perfect. the paint came off easily w/ acetone, im gonna get around to refinishing them someday. |
|
Has anyone found a good way to clean up mags that have cosmoline coating the inside and outside of the mags? I have about 20 to clean, but have been putting it off in hopes of finding a better way. I had used hot water and Simple Green, and that didn't work to well. I understand that cosmoline melts at 140 degrees, so I was going to get try a lot hotter water the next time. The mags seem to be dipped in the cosmoline. Anybody found a good way to completely remove the cosmoline? Sure could use a better way to do this. |
|
To remove the cosmoline ... I soak the magazines in hot water and Dawn dish soap .. then throw them in the dishwasher ... Oh.. did I tell you I was single ...? So I do not have to contend with a lady of the house ... now of course that is looking to change ... but til then I can use the kitchen sink for hte over night magazine soak .. Ted... |
Armory Sponsor