User Panel
Originally Posted By JohnnyUtah427: I took the skyscraper off, since I don't run magnifier and I took off the BUIS to run the Atpial as far forward as I can, but I still run a 2.26" height optic mount (Unity FAST). And yea...I LOVE a high mount red dot as the heads up shooting is so much faster, more comfortable, and more modern. Highly recommend it, but practice, practice, practice. https://live.staticflickr.com/65535/51732226990_e1b7e00eb9_b.jpg View Quote Second this on my 11.5 CQB. Went from a Skyscraper to a Unity because I don't run a magnifier as well. |
|
|
I took a class with my skyscraper mount. I think if most of your shooting is going to be inside of 100 yards, it’s quite good. It is a little uncomfortable in the prone position because you have to lift your chest and head up a little bit to look through the tube appropriately. It might not be as bad if you have a chest rig in a lot of gear on because that would raise your body up a little bit. I may be a touch quicker from the low ready with it on. It’s good to try and see how you adapt to it, as it mates with the CQB gun quite well. That’s where I see it being applied. I have lower third co witness on my 14.5s bc I shoot orone more with them. I also don’t think it’s such a drastic change over a lower third cowitness to where you can’t have multiple guns set up differently and you’re proficient with them all. It does change your height over bore close in enough that it matters. Try one out, practice, and I think you’ll end up keeping it on at least one gun.
|
|
|
Runs flawlessly Attached File
|
|
1st Battalion 6th Marines Bravo Company
|
Originally Posted By FastCar: @ARogueNinja @JohnnyUtah427 @DetroitSounds @eMc9001 @buddyhoohaw How do you guys like the KAC Skyscraper Mount for the Aimpoint T1/T2 compared to a lower 1/3 co-witness mount, on a KAC 11.5" CQB SBR ? I'm strongly considering a KAC Skyscraper and would like to get some real world feedback from actual users that are NOT using it with night vision because I don't have or plan to gets NODS at this time. If you could do it over again would you go with the Skyscraper or stick with the lower 1/3 co-witness you had before the KAC Skyscraper? I read every thread out there already and can't really find a good answer/explaination. Only thing of value I saw was that the KAC Skyscraper is very uncomfortable in the prone position. View Quote I've gone back and forth but I did just run a 600 round session with CQB with the High rise/ M5. I dig it but went back to 1.93. Although it's only a slight height difference, I'm really dialed in with 1.93. Right now I have an ATACR on 1.93 on SR25, NX8 on a 1.93 and so on, so every rifle feels the same. Hardly a big deal though. I'd say give it a try along with a 1.93, see what ya like. |
|
|
1st Battalion 6th Marines Bravo Company
|
|
Champion of the Sun, Master of Karate & Friendship
VA, USA
|
|
|
|
|
@5L33P3R URX get damaged or just wanted to swap to LDR1?
|
|
|
|
|
Think I found a ambi lower for my new mk 2 upper, but prior to that I was debating just buying a complete gen 4 Noveske ambi rifle to put the lower on my Sr15, I’ve wanted a Noveske since I was a kid, I know they are a life style brand a la Q post John, but their stuff still is beautiful and looks super high quality. Now I have an extra radian lower laying around, so maybe I’ll go Noveske for my competition upper.
|
|
|
Originally Posted By convexx: A lot of blasphemy going on here: Surefire OBC with E-3 bolt and cam pin. Radian ADAC lower. https://www.ar15.com/media/mediaFiles/559191/2022-03-19_9-36-09-2318796.png View Quote The Radian lowers are real nice, but I couldn't justify the $100 uncharge over a ADM which is also a great ambience lower. Bet it's a great shooter. |
|
|
Originally Posted By friskydingo: The Radian lowers are real nice, but I couldn't justify the $100 uncharge over a ADM which is also a great ambience lower. Bet it's a great shooter. View Quote I usually buy them partially stripped (missing trigger) on notifications from dealers. ADM is great as well. It's a great shooter for sure, and the Surefire OBC helps a lot. |
|
|
Originally Posted By captainhaggs: Think I found a ambi lower for my new mk 2 upper, but prior to that I was debating just buying a complete gen 4 Noveske ambi rifle to put the lower on my Sr15, I’ve wanted a Noveske since I was a kid, I know they are a life style brand a la Q post John, but their stuff still is beautiful and looks super high quality. Now I have an extra radian lower laying around, so maybe I’ll go Noveske for my competition upper. View Quote I have a Gen4 lower on an 11.5" as well. Great stuff. I love KAC but my (KAC) lowers have so much slop when running the KAC uppers that I decided long ago to go billet for the lowers. You'll love the Gen4 lower. |
|
|
Failure has far too many fathers. -MMB
|
|
Took some more employees out to shoot Knights for their first time.
Attached File Attached File Attached File Attached File |
|
|
Originally Posted By convexx: Upper/lower fitment isn't great, even on factory guns, so I run Radian lowers on my KAC uppers. You do you. View Quote View All Quotes View All Quotes Originally Posted By convexx: Originally Posted By buddyhoohaw: WTF? Upper/lower fitment isn't great, even on factory guns, so I run Radian lowers on my KAC uppers. You do you. Weird, all of my Kacs are tight as a drum...have never known anyone with looseness either....did you try having Kac check it out? |
|
|
|
Originally Posted By convexx: Upper/lower fitment isn't great, even on factory guns, so I run Radian lowers on my KAC uppers. You do you. View Quote Nothing wrong with mix-matching KAC uppers to XYZ lowers but to say its because KAC fitment isn't great seems off to me. How many have you had fitment issues with? Cheers |
|
Failure has far too many fathers. -MMB
|
Originally Posted By buddyhoohaw: Nothing wrong with mix-matching KAC uppers to XYZ lowers but to say its because KAC fitment isn't great seems off to me. How many have you had fitment issues with? Cheers View Quote I've had three SR lowers. Two of the three had lots of slop. I know it's not an issue functionally but I always ran an accu-wedge in them with KAC uppers. |
|
|
|
|
Originally Posted By convexx: I have a Gen4 lower on an 11.5" as well. Great stuff. I love KAC but my (KAC) lowers have so much slop when running the KAC uppers that I decided long ago to go billet for the lowers. You'll love the Gen4 lower. View Quote All of my KAC's have had a bit of slop. Easiest fix is the JP micro sized pins for the SR15's. Most of my guns I got away with just the slightly bigger pins, but one of my factory guns I needed to use the "extra oversized" takedown pins due to how much slop there was. But, it's perfect now. No need to throw foam or rubber wedges in your lowers if you don't want to. It's a permanent solution. FYI no bueno for the SR25. The JP pins are too short. |
|
|
Originally Posted By AndysAR15name: All of my KAC's have had a bit of slop. Easiest fix is the JP micro sized pins for the SR15's. Most of my guns I got away with just the slightly bigger pins, but one of my factory guns I needed to use the "extra oversized" takedown pins due to how much slop there was. But, it's perfect now. No need to throw foam or rubber wedges in your lowers if you don't want to. It's a permanent solution. FYI no bueno for the SR25. The JP pins are too short. View Quote |
|
|
Originally Posted By Regency: I'm looking at their website, did you order the 'oversize', 'standard', or 'undersize' ? View Quote If he is trying to remove slop, I would expect him to use the oversize pins. The undersize pins are used if the upper and lower are too tight and difficult to get the pins out for takedown. If you have slop, the oversize is what you want. |
|
|
Wish they sold the Noveske gen 4 lower separate of the rifle, anyone try a gen 4? I know everyone says they’re a lifestyle brand now?
Their guns always looked Gucci as hell and were top of the market. Has quality really decreased so much since John and his right hand dude left? |
|
|
Originally Posted By duckhook02: If he is trying to remove slop, I would expect him to use the oversize pins. The undersize pins are used if the upper and lower are too tight and difficult to get the pins out for takedown. If you have slop, the oversize is what you want. View Quote View All Quotes View All Quotes Originally Posted By duckhook02: Originally Posted By Regency: I'm looking at their website, did you order the 'oversize', 'standard', or 'undersize' ? If he is trying to remove slop, I would expect him to use the oversize pins. The undersize pins are used if the upper and lower are too tight and difficult to get the pins out for takedown. If you have slop, the oversize is what you want. That’s right. If you have a little slop the oversized will help tighten that right up. If you have a lot of slop, they sell an “extra oversized” which will tighten up even the loosest fitting gun. But with the extra oversized you run the risk of making your gun too tight and not being able to separate the upper and lower with just your fingers. You might need a bullet or something. Winning combo i’ve found is extra oversized up front, since I never remove that anyways, and just an oversized in the rear. This allows you to still pop out the rear to service the gun/clean etc, and should completely tighten up the loosest of the SR15s out there. |
|
|
Awesome. Thanks for the info on the OS-pins. I am going to order a few pairs today.
|
|
|
Originally Posted By captainhaggs: Wish they sold the Noveske gen 4 lower separate of the rifle, anyone try a gen 4? I know everyone says they’re a lifestyle brand now? Their guns always looked Gucci as hell and were top of the market. Has quality really decreased so much since John and his right hand dude left? View Quote I own two Gen4s. One was a complete rifle with a 16" SS upper in Bazooka Green. I sold the upper and kept the lower. I shoot a lot and only run CHF/CL barrels. SS is great but not for me. I have another Gen4 lower pulled from another complete rifle. I think that the lowers are fantastic quality; on par with Radian and other top tier billet lowers. I prefer it aesthetically to the Radian but both are great. I like how slim the NSR handguards are, but I think the attachment sucks. Just dumb. Lining up the screws? C'mon. I had a CHF switchblock upper on my SBR lower that was a laser, but so heavy. |
|
|
Kudos to those who shoot their guns. Most seem to be fixated with what they are worth
|
|
|
|
|
|
|
Originally Posted By VinnyElCamino: I don’t often photograph my firearms, but the 14.5 looked good yesterday. https://www.ar15.com/media/mediaFiles/551999/4F045E6B-F56A-478C-80E1-2B68DF775ED7_jpe-2332853.JPG View Quote Diggin the color. What is it? |
|
God will not look you over for medals, diplomas, or degrees – but for scars
|
Field Drab + Olive Drab
|
|
|
|
Originally Posted By JohnnyUtah427: https://live.staticflickr.com/65535/51950286793_31727f1ae8_b.jpg View Quote So many of us running the skyscraper. Is that a full power PEQ-15? Want to sell it? |
|
|
Originally Posted By convexx: Rattlecan is the only way. ;) View Quote View All Quotes View All Quotes Originally Posted By convexx: Originally Posted By VinnyElCamino: Field Drab + Olive Drab Rattlecan is the only way. ;) FYI...Aervoe is dropping their .mil camo paint line according to Big Tex, so buy the colors that you like now. |
|
God will not look you over for medals, diplomas, or degrees – but for scars
|
Originally Posted By SecretSquirell: FYI...Aervoe is dropping their .mil camo paint line according to Big Tex, so buy the colors that you like now. View Quote I picked up quite a few when they had like a buy 5 get 1 free sale + their discount code. Aervoe is definitely the best rattlecan option available imo |
|
|
Failure has far too many fathers. -MMB
|
I've been using Aluma-Hyde, but I don't like giving Brownells any cash. I'll buy some, thanks.
|
|
|
Originally Posted By VinnyElCamino: I picked up quite a few when they had like a buy 5 get 1 free sale + their discount code. Aervoe is definitely the best rattlecan option available imo View Quote View All Quotes View All Quotes Originally Posted By VinnyElCamino: Originally Posted By SecretSquirell: FYI...Aervoe is dropping their .mil camo paint line according to Big Tex, so buy the colors that you like now. I picked up quite a few when they had like a buy 5 get 1 free sale + their discount code. Aervoe is definitely the best rattlecan option available imo I snagged up some during that sale too. Had to grab some more FD as my one in-use can stopped spraying and the 2 that I had never used refused to spray as well. |
|
God will not look you over for medals, diplomas, or degrees – but for scars
|
Originally Posted By buddyhoohaw: Aervoe is very impressive paint. Sorry to see it go. Cheers View Quote View All Quotes View All Quotes Originally Posted By buddyhoohaw: Originally Posted By SecretSquirell: FYI...Aervoe is dropping their .mil camo paint line according to Big Tex, so buy the colors that you like now. Aervoe is very impressive paint. Sorry to see it go. Cheers Yup. Properly applied and cured, the shit is almost like a coating. |
|
God will not look you over for medals, diplomas, or degrees – but for scars
|
|
Perfection Attached File
|
|
1st Battalion 6th Marines Bravo Company
|
Nice. RC2 and a high power PEQ.
|
|
|
Sign up for the ARFCOM weekly newsletter and be entered to win a free ARFCOM membership. One new winner* is announced every week!
You will receive an email every Friday morning featuring the latest chatter from the hottest topics, breaking news surrounding legislation, as well as exclusive deals only available to ARFCOM email subscribers.
AR15.COM is the world's largest firearm community and is a gathering place for firearm enthusiasts of all types.
From hunters and military members, to competition shooters and general firearm enthusiasts, we welcome anyone who values and respects the way of the firearm.
Subscribe to our monthly Newsletter to receive firearm news, product discounts from your favorite Industry Partners, and more.
Copyright © 1996-2024 AR15.COM LLC. All Rights Reserved.
Any use of this content without express written consent is prohibited.
AR15.Com reserves the right to overwrite or replace any affiliate, commercial, or monetizable links, posted by users, with our own.