User Panel
Hello everyone,
Long time lurker, first time poster. I recently purchased a bunch of polymer lowers and am considering my first from-scratch build to be an SBR and I was going to get an engraver to go ahead and get at least 2 of them done. There is a very small amount of aluminum that is used for structural integrity and a small section of it was left exposed for an engraved S/N. My question is, since there is no metal portion to be engraved, would engraving on the polymer be acceptable as "permanent"? For example "American Tactical Summerville, SC" is embossed into the polymer. I'll start on getting the required paperwork filled out in the next couple of days and I'm sure I'll have more questions then. This thread has been a great resource to get me started though, so thanks everyone for that. |
|
|
First off, BigWaylonThanks for all the info on submitting a Form 1, your step by step tutorial is awesome. I'm not sure if this has been answered or even asked, but for question 4d for model, I'm not sure what to put down, I'm using a Sig Sauer M400 lower for my SBR, and there is no "model" designation, other than SIG on the mag well and the sn and manufacturer & city info above the trigger. I know your previous answers have specified to put what is on the lower. Should I leave it blank or should I put down SIG? Thanks in advance.
|
|
|
Originally Posted By WarriorSoulM4:
First off, BigWaylonThanks for all the info on submitting a Form 1, your step by step tutorial is awesome. I'm not sure if this has been answered or even asked, but for question 4d for model, I'm not sure what to put down, I'm using a Sig Sauer M400 lower for my SBR, and there is no "model" designation, other than SIG on the mag well and the sn and manufacturer & city info above the trigger. I know your previous answers have specified to put what is on the lower. Should I leave it blank or should I put down SIG? Thanks in advance. View Quote On top of that, it seems the ATF has access to manufacturer info (or maybe just a database of previous info) that has model name. I say that because they often give suggestions when they send out an error letter. So...you might put something down that is different from what they think it should be. Others may be able to give you a better answer...but I'll tell you want I'd do. I'd take a pic of both sides of the receiver showing all engravings, put "N/A" in 4d, and then print the pics on a single sheet of paper along with a sentence saying you put N/A because the model wasn't designated on the receiver. The regulation says the model has to be engraved, if designated. (My F1 suppressors have N/A on the F1s for model, and I didn't engrave anything for model). I'd send that sheet in with my forms. Odds are no matter what I chose to do, they'd send an error letter requesting something different. |
|
|
Originally Posted By CH1N4:
Hello everyone, Long time lurker, first time poster. I recently purchased a bunch of polymer lowers and am considering my first from-scratch build to be an SBR and I was going to get an engraver to go ahead and get at least 2 of them done. There is a very small amount of aluminum that is used for structural integrity and a small section of it was left exposed for an engraved S/N. My question is, since there is no metal portion to be engraved, would engraving on the polymer be acceptable as "permanent"? For example "American Tactical Summerville, SC" is embossed into the polymer. I'll start on getting the required paperwork filled out in the next couple of days and I'm sure I'll have more questions then. This thread has been a great resource to get me started though, so thanks everyone for that. View Quote The regulation says: The serial number must be placed in a manner not susceptible of being readily obliterated, altered, or removed, and must not duplicate any serial number placed by you on any other firearm. Do the commercial polymer firearms have metal plates for the SN? The regulation doesn't specify "metal", so I'm not sure it matters. Anybody ever seen the ATF answer a question on this? |
|
|
Originally Posted By BigWaylon:
I don't have a definite answer on that. The problem is that if you put something in the box, it's supposed to be engraved. So, if you put something there that's not already on the firearm, you'd be responsible for getting it added. On top of that, it seems the ATF has access to manufacturer info (or maybe just a database of previous info) that has model name. I say that because they often give suggestions when they send out an error letter. So...you might put something down that is different from what they think it should be. Others may be able to give you a better answer...but I'll tell you want I'd do. I'd take a pic of both sides of the receiver showing all engravings, put "N/A" in 4d, and then print the pics on a single sheet of paper along with a sentence saying you put N/A because the model wasn't designated on the receiver. The regulation says the model has to be engraved, if designated. (My F1 suppressors have N/A on the F1s for model, and I didn't engrave anything for model). I'd send that sheet in with my forms. Odds are no matter what I chose to do, they'd send an error letter requesting something different. View Quote View All Quotes View All Quotes Originally Posted By BigWaylon:
Originally Posted By WarriorSoulM4:
First off, BigWaylonThanks for all the info on submitting a Form 1, your step by step tutorial is awesome. I'm not sure if this has been answered or even asked, but for question 4d for model, I'm not sure what to put down, I'm using a Sig Sauer M400 lower for my SBR, and there is no "model" designation, other than SIG on the mag well and the sn and manufacturer & city info above the trigger. I know your previous answers have specified to put what is on the lower. Should I leave it blank or should I put down SIG? Thanks in advance. On top of that, it seems the ATF has access to manufacturer info (or maybe just a database of previous info) that has model name. I say that because they often give suggestions when they send out an error letter. So...you might put something down that is different from what they think it should be. Others may be able to give you a better answer...but I'll tell you want I'd do. I'd take a pic of both sides of the receiver showing all engravings, put "N/A" in 4d, and then print the pics on a single sheet of paper along with a sentence saying you put N/A because the model wasn't designated on the receiver. The regulation says the model has to be engraved, if designated. (My F1 suppressors have N/A on the F1s for model, and I didn't engrave anything for model). I'd send that sheet in with my forms. Odds are no matter what I chose to do, they'd send an error letter requesting something different. |
|
|
Sorry to rehash this thread but hopefully someone can help me understand something with the Form 1.
Filing as individual, section 4c, 4d, and 4g: For an AR lower, do I use the model and serial number that's already on the receiver from Anderson, or as the "maker" of the SBR, do I come up with my own serial number, such as "001" or something? CAN I use Anderson's serial number to make it easier? Section 4h: Walkthrough thread here says used to be left blank, but now you enter the information you'll engrave on the receiver. Would that information to be engraved be the following: XXXX (serial number no smaller than 1/16th inch, .003 depth) AR-15 5.56mm (model and caliber, .003 depth) John Q. Public, Anytown, NY USA (makers name and place SBR was made, .003 depth) Also, is there any way to have it be for multiple calibers, or would I need to list each caliber I "might" ever want? Thanks |
|
|
Does location of engraving matter as long as it is on the receiver? A company I have been looking at to engrave mine offers the option to engrave under the receiver above and below where the trigger comes out so it would be hidden.
|
|
|
Originally Posted By jjustice322:
Does location of engraving matter as long as it is on the receiver? A company I have been looking at to engrave mine offers the option to engrave under the receiver above and below where the trigger comes out so it would be hidden. View Quote THSF does a lot of engraving around the trigger hole. You could also put it on the front the magwell and most would never notice it. The one AR I had to add caliber to got it out right between get pivot pin ears with a dremel...completely visible, but can't imagine anybody ever noticing it. There's not even a regulation saying it has to be in the same location, or on the same part. And remember, all the stuff (other than SN) only has a minimum depth requirement...so it can be tiny. |
|
|
@BigWaylon can you help me out?
Is it legal to travel interstate with a sbr lower using a 16” barrel? And do you need a 5320.20 for a suppressor to travel out of state? I know that they are both legal to do, but I can’t find the language or the answer on the FAQ page. |
|
"Good people do not need laws to tell them to act responsibly, while bad people will find a way around the laws." - Plato
|
Originally Posted By TATBME:
@BigWaylon can you help me out? 1. Is it legal to travel interstate with a sbr lower using a 16” barrel? 2. And do you need a 5320.20 for a suppressor to travel out of state? I know that they are both legal to do, but I can’t find the language or the answer on the FAQ page. View Quote 2. No. Look at the F1/F4 and the 5320.20. All mention interstate travel, and only list SBR/SBS/MG/DD. AOWs and silencers do not require the form (but you could still have local restrictions) |
|
|
Edit: Nevermind, found the answer.
|
|
I'm too drunk to taste this chicken.
|
@elkoholic
|
|
If we do meet again, why, we shall smile; If not, why, then, this parting was well made".
|
@BigWaylon I filled out the pdf form of the 5320.20, do you know the email address that I’m supposed to send it to? I’ve always went the snail mail route, that I’d try something different.
|
|
"Good people do not need laws to tell them to act responsibly, while bad people will find a way around the laws." - Plato
|
Originally Posted By TATBME:
@BigWaylon I filled out the pdf form of the 5320.20, do you know the email address that I’m supposed to send it to? I’ve always went the snail mail route, that I’d try something different. View Quote You would, too...if you read the instructions (page 3) on the form. The fax number and email address are there. |
|
|
Ok...have my first sbr. Did the trust....this way my fam can shoot my sbr and stuff. I didnt put them on yet becauae I knew I was gonna be adding another sbr to the trust. When this one is said and done..I will adding them.
Now I know some things have changed with paper work over the year or two since my first sbr. Last time I went with silencer shop, what is a easier way to do it this time? And how do I add this one to the trust...the first time was confusing as hell and this is no different. I know I have to get this lower engraved also, and I should engrave it the same way as the other lower, right? Meaning name on it and all? Thanks guys...I really appreciate your time. |
|
IN A NEW YORK STATE OF MIND.
|
You file a Form 1 (assuming you’re making the SBR and not buying an existing one). EForms is the way to go at this time. The submitter will be the trust...so the firearm is registered to the trust.
How you document it with the trust is specific to the trust. Some use schedules, some use assignment sheets, some may use both, and some may do something else. ETA: and nothing has changed with the engraving requirements |
|
|
I submitted the F1 for my AR lower, it currently has a rifle upper but was originally a pistol.
Once I have the approval and engraving, it is only a NFA item with the rifle stock on it correct, if I swap on a SBA3 stock and it has a 10.5" upper it is no longer a NFA item correct. Also is it still ok to swap to different barrel length uppers or does it need to remain at 10.5" like I filled out initially. |
|
|
Not sure if this is the thread to ask this question-
When engraving a Form 1 SBR, what if I don't live within city limits? Do use the town on my mailing address or just the county? |
|
|
Originally Posted By SilverLightning: Not sure if this is the thread to ask this question- When engraving a Form 1 SBR, what if I don't live within city limits? Do use the town on my mailing address or just the county? View Quote Use the city and state from block 3B on your approved Form 1. |
|
|
Form 1 SBR engraving question - I have an 80% lower that I want to have specific personally-amusing engravings, but it's also going to be a registered SBR. If the front of the magwell gets the proper (real name, location et cetera) markings, would I use those for the registration and still be able to run (for example) "Nerf Firearms Division, Fun City, West Pensyltucky" in the traditional left-side-receiver location?
|
|
|
Originally Posted By Ygolonac: Form 1 SBR engraving question - I have an 80% lower that I want to have specific personally-amusing engravings, but it's also going to be a registered SBR. If the front of the magwell gets the proper (real name, location et cetera) markings, would I use those for the registration and still be able to run (for example) "Nerf Firearms Division, Fun City, West Pensyltucky" in the traditional left-side-receiver location? View Quote Are you asking if you can do both of these? 1. Engrave all the required info in an acceptable spot 2. Engrave additional nonsense anywhere on the firearm If so, I know of no regulation that would prevent #2 as long as #1 happened. |
|
|
Originally Posted By BigWaylon: Are you asking if you can do both of these? 1. Engrave all the required info in an acceptable spot 2. Engrave additional nonsense anywhere on the firearm If so, I know of no regulation that would prevent #2 as long as #1 happened. View Quote Cool, just wanted to verify. Thanks! |
|
|
Potentially dumb question here:
If I already have a trust due to my suppressor, do I have to redo my fingerprints when I do a Form 1 to turn my MP5 pistol into an SBR? Also, how am I to accurately measure OAL if it will change once I swap from the current brace to the end game stock? Thanks for the help, these BS laws are confusing so far for me. |
|
|
Originally Posted By CJ47: Potentially dumb question here: If I already have a trust due to my suppressor, do I have to redo my fingerprints when I do a Form 1 to turn my MP5 pistol into an SBR? Also, how am I to accurately measure OAL if it will change once I swap from the current brace to the end game stock? Thanks for the help, these BS laws are confusing so far for me. View Quote I believe you do have to submit new prints. That used to be the good thing about a Trust... No prints. Of course that's all changed now. Anyway... FYI: You can submit multiple Form 1's on one set of prints. As far as OAL, measure with brace then measure stock, add or subtract as necessary. |
|
> Have gun, will travel <
|
Ugh... e-Filling out a Form 1 as an individual right now to SBR an AR15, and it has me confused.
I see no instructions for this stuff on the eFile website.
|
|
WITH....a HERRING!
|
Originally Posted By madmedic: Ugh... e-Filling out a Form 1 as an individual right now to SBR an AR15, and it has me confused. I see no instructions for this stuff on the eFile website.
View Quote CLEO - its so you can mail it, but you have to fill in the details still. You can go online and request fingerprint cards from the ATF (free) and roll your own. You can buy them from Amazon also with the ink to roll them. Or you can possibly get your CLEO agency to do it. ATF how to do it; https://www.atf.gov/firearms/docs/form/fingerprint-card-instructions-and-example-fd-258 ATF Free Cards; https://www.atf.gov/distribution-center-order-form |
|
|
Originally Posted By madmedic: Ugh... e-Filling out a Form 1 as an individual right now to SBR an AR15, and it has me confused. I see no instructions for this stuff on the eFile website.
View Quote Print out a paper Form 1 and have it with you as you go through eForms. It’ll help. It also has examples of who qualified as CLEO, if you’ll actually read the instructions. (Hint: I’ve never sent anything to my Sheriff) |
|
|
Dumb questions from me.
Looking to SBR my poser Mp5. (AP5) and I see that they need the exact OAL on the form? Now I am not sure if I am going A2 stock (Most likely) but want to be able to try an A3 . Not exact OAL close but not exact. If I go A3 stock it is measured extended or collapsed? If I go with one stock then change it out is that a no no? Say A2 to A3? or vice versa? |
|
|
Originally Posted By WildBoar: Dumb questions from me. Looking to SBR my poser Mp5. (AP5) and I see that they need the exact OAL on the form? Now I am not sure if I am going A2 stock (Most likely) but want to be able to try an A3 . Not exact OAL close but not exact. If I go A3 stock it is measured extended or collapsed? If I go with one stock then change it out is that a no no? Say A2 to A3? or vice versa? View Quote Look at a paper copy of the form. The answer on how to measure is there. Description of Firearm and Markings. (1) Item 4a. If you are modifying an existing firearm, enter the name and location of the original manufacturer. If you are creating the firearm, enter the maker’s name, city and state. (2) Item 4b. The types of NFA firearms are listed in the definitions; (3) Item 4c. Specify one caliber or gauge. If there is another designation, indicate the designation in item 4h. (4) Item 4d. Show the model designation (if known). (5) Item 4e and 4f. Specify one barrel length and overall length in items 4e and 4f as applicable. Note: if the firearm has a folding or collapsible stock, the overall measurement is to be made with the stock extended. (6) Item 4g. Do not alter or modify the serial number of an existing firearm . Enter the existing serial number or, if a new firearm, one you create. (7) Markings: The maker is required to mark the firearm with the maker’s name, city and state as shown in item 3b. All markings are to be in compliance with 27 CFR 478.92 and 479.102. Changing stocks after the fact is a non-issue. Just submit something close, round to the nearest inch is fine. |
|
|
Cool. Thanks. I just saw other comments seeming like they needed exact and wasn't sure if I would catch crap If I later swapped it out and they wanted to be dicks later.
|
|
|
This is a dumb question…I have a trust via SilencerShop. Am I able to form1 SBR my gun as an individual, outside of the trust? The reason I ask is I’m not sure about the process to add an SBR to the trust, and it seems like a hassle.
Assuming I can file as individual, am I right in the idea that later down the line if I wanted to add said SBR to my family trust I could do that? This stuff confused me to death, I really need to learn it better. |
|
On Guard Defense Training Center
|
Originally Posted By CJ47: This is a dumb question…I have a trust via SilencerShop. Am I able to form1 SBR my gun as an individual, outside of the trust? The reason I ask is I’m not sure about the process to add an SBR to the trust, and it seems like a hassle. Assuming I can file as individual, am I right in the idea that later down the line if I wanted to add said SBR to my family trust I could do that? This stuff confused me to death, I really need to learn it better. View Quote You can always file as an individual. Or file as a different entity. You can then add it to the trust…for $200. You have to file a Form 4 and transfer it from you to the trust. |
|
|
Originally Posted By BigWaylon: You can always file as an individual. Or file as a different entity. You can then add it to the trust…for $200. You have to file a Form 4 and transfer it from you to the trust. View Quote Now…if I do file individual, and decide to add it to the trust, during the Form 4 waiting period am I allowed to use it? Or would it have to stay locked up? |
|
On Guard Defense Training Center
|
Originally Posted By CJ47: Now…if I do file individual, and decide to add it to the trust, during the Form 4 waiting period am I allowed to use it? Or would it have to stay locked up? View Quote You’ll be the transferee and transferor, so it’s yours no matter what. Approved? Yours as a trustee. Disapproved? Stays your as an individual. During the wait? Still property of yours as an individual…so do whatever you want to with it. |
|
|
Originally Posted By BigWaylon: You’ll be the transferee and transferor, so it’s yours no matter what. Approved? Yours as a trustee. Disapproved? Stays your as an individual. During the wait? Still property of yours as an individual…so do whatever you want to with it. View Quote Thank you so much. That will make it a lot easier for me. |
|
On Guard Defense Training Center
|
It's been a long time but what needs to be engraved on a lower now when you're the maker of an SBR with multi as caliber by manufacturer ?
Trust name City, State And can the caliber be marked on barrel still? .223/5.56? |
|
|
My trust has a giant fucking name. I guess I am skipping the SBR route on my AP5
Sucks that it has to be plainly visible. I don't it will fit anywhere on that gun? |
|
|
Originally Posted By A96HondaAccordEX: It's been a long time but what needs to be engraved on a lower now when you're the maker of an SBR with multi as caliber by manufacturer ? Trust name City, State And can the caliber be marked on barrel still? .223/5.56? View Quote Yes and yes. Have to pick a caliber to get the Form 1 approved because they don't do "multi". Keep the upper around to return it to the approved configuration if it's ever needed. |
|
|
Originally Posted By WildBoar: My trust has a giant fucking name. I guess I am skipping the SBR route on my AP5 Sucks that it has to be plainly visible. I don't it will fit anywhere on that gun? View Quote You could always do it as an individual. My SBR's are engraved on the inside lip of the magwell. Plainly visible when the mag is dropped. |
|
|
|
Originally Posted By WildBoar: Doesn't individual require CLEO Sign off? (going by the 1st post link) View Quote View All Quotes View All Quotes Originally Posted By WildBoar: Originally Posted By HammerTech: You could always do it as an individual. My SBR's are engraved on the inside lip of the magwell. Plainly visible when the mag is dropped. Doesn't individual require CLEO Sign off? (going by the 1st post link) No. That went away with 41F. There is a notification, but the CLEO does not have to "approve." I just did 2 individual form 1's in August and September. |
|
|
|
I have a trust with a number of suppressors and SBR's but I haven't done an SBR in a long time. I vaguely remember something about needing photos of myself and the other responsible party even with a trust now? is that the case? or can I just send off the fingerprint cards and no passport photos after I file the eform? |
|
|
Originally Posted By Quarterbore: Originally Posted By jercdevil: Do the SBR have to be built on a preban lower. I would assume so otherwise you could not have an telescopic stock. I have to very nice preban colts in the safe,but I would hate to take a engraver to them. I see this was answered below and it is on page 1 of the FAQ... quarterbore.com/library/pdf_files/shortbarreledriflefaq.pdf View Quote Is there an updated link to this FAQ? The domain is for sale, any links to it currently don't work. |
|
"Evil preaches tolerance until it is dominant, then it tries to silence good."
|
If you have a lower marked with Caliber Multi, can you use two different upper receivers of different calibers and lengths?
So like 12.5" Barrel 5.56mm 8" Barrel 300 blackout On the same lower |
|
Proud millennial.
|
I realize the OP is 14 years old, but the link is broken and the website is offline. Maybe it needs to be updated or unstickied.
|
|
Proud millennial.
|
Since this thread seems to be abandoned/useless, this website SBR step by step is very helpful and answers most questions.
|
|
|
Does a CAA MCK with a pistol installed as well as a brace on the MCK require an SBR stamp? I have tried to research it on my own but can't find anything definitive about it.
Thanks |
|
Democratic party=new communist party
|
The FAQ in the first post is going to a dead link, or am I missing something?
|
|
A people that values its privileges above its principles soon loses both. - Dwight D. Eisenhower
|
I guess I should have asked this here.....
Can you abbreviate your name on the engraving when you do a form1 lower? John Doe City, OH Instead of Johnathan Lee Doe City, OH |
|
“If liberty means anything at all it means the right to tell people what they do not want to hear.”
George Orwell, Animal Farm |
Sign up for the ARFCOM weekly newsletter and be entered to win a free ARFCOM membership. One new winner* is announced every week!
You will receive an email every Friday morning featuring the latest chatter from the hottest topics, breaking news surrounding legislation, as well as exclusive deals only available to ARFCOM email subscribers.
AR15.COM is the world's largest firearm community and is a gathering place for firearm enthusiasts of all types.
From hunters and military members, to competition shooters and general firearm enthusiasts, we welcome anyone who values and respects the way of the firearm.
Subscribe to our monthly Newsletter to receive firearm news, product discounts from your favorite Industry Partners, and more.
Copyright © 1996-2024 AR15.COM LLC. All Rights Reserved.
Any use of this content without express written consent is prohibited.
AR15.Com reserves the right to overwrite or replace any affiliate, commercial, or monetizable links, posted by users, with our own.