Quoted:
I missed a zinga

Please accept this as my penance

https://media2.giphy.com/media/zWXgy8HXXd29y/giphy.gif?cid=5e214886cb4wozdqh3uy48wwd5ppjkyt5e6osrlxv6zxtgve&rid=giphy.gif&ct=g

Quoted:
Gas has gone up 44 cents in the past week. Diesel is at 3.99 now

Quoted:
Gas has gone up 44 cents in the past week. Diesel is at 3.99 now

Quoted:

Trade you a nice little fuel efficient car

Quoted:
Gas has gone up 44 cents in the past week. Diesel is at 3.99 now

Quoted:
Id rather live in ohio than here

Quoted:
I need that blank post trick  nao!

Quoted:
Needs to be lunchtime

Quoted:
Gas has gone up 44 cents in the past week. Diesel is at 3.99 now

Quoted:
@RalphBacon

M16 with AN/PVS-1 Starlight scope and XM148 grenade launcher.

https://www.ar15.com/media/mediaFiles/259822/274746174_1245570689307278_6764531522343-2300910.JPG

Quoted:
Time to log off and go talk to my cows

Quoted:
Birds aren't real

Quoted:
Time to log off and go talk to my cows

Quoted:
This shit is gonna get out of hand.

Quoted:


Additional steps: eForm 1 Silencer submission

Dear eForm 1 applicant,

The National Firearms Act (NFA) Division received your ATF eForm 1, Application to Make and Register a Firearm. As a part of the application process, NFA Division must confirm that the making or possession of a firearm would not place the applicant in violation of law.[1]  

NFA Division requests that you provide certain additional information so that it may determine whether your eForm 1 application to make a silencer may lawfully be approved. Specifically, please submit to NFA Division the following:

Pictures of the parts that you will use to make the silencer (the pictures should be clear and allow the identification of the parts photographed),
A description of the processes you will use to assemble or fabricate the silencer,
The product, model, or kit name, if any, of each device and/or part that you will use to make the silencer, and
The source from which the parts were obtained, i.e., the name of the store, website, etc.
The additional information may be submitted to NFA Division at the following email address: [email protected]. Please include the form Permit Control Number or eForm ID in the Subject bar for each correspondence with attachments. The additional information may also be sent by mail to:

Bureau of Alcohol, Tobacco, Firearms and Explosives

National Firearms Act Division

244 Needy Road

Martinsburg, WV25405

Without the additional descriptive information, NFA Division will be unable to determine whether the eForm 1 application to make a silencer may lawfully be approved. Therefore, failure to submit the requested information by March 25, 2022, will result in your application being disapproved and your $200.00 making tax refunded.

Questions regarding this email should be directed to [email protected]. If you have additional inquiries, please call 304-616-4500.

[1] An ATF Form 1 application to make a silencer cannot lawfully be approved if the maker will make the silencer with parts that are themselves classified as silencers under federal law and the parts were transferred to the maker without complying with the tax, transfer, and registration requirements of the NFA. An approved Form 1 does not authorize any person to manufacture the silencer on behalf of the Form 1 maker. An approved Form 1 does not authorize the transfer of a silencer to the Form 1 maker. A subsequently approved Form 1 does not legitimize the transfer of a silencer that did not comply with the tax, transfer, and registration requirements of the NFA. Further, it is a violation of the NFA to make a false entry on any NFA application. 26 U.S.C. 5861(l). The maker must certify on the Form 1 application that the maker is the person who will make the silencer identified on the Form 1 application. The maker’s certification is a false entry on the Form 1 application if the maker’s Form 1 silencer was manufactured by another person.