User Panel
|
I've been reading this thread for quite sometimes, finally got the fnh lower and HCS mod1 upper from kev. I am looking to get leupold 112633 TS30a2, however I am not sure which one has the mk12 mod1 bdc turret and which one has the 7.62mm 168gr bdc. They both use the same 112633 part number, most of the reseller just copy and pasted the description from leupold. I called couple place this afternoon, opticplanet, amazon, and midwayusa, no one knows.
Thanks |
|
|
Originally Posted By Mattyvac: Those m1 turrets tho so ugly In all honesty, once you zero an mr/t scope with mk262 at 100, you just use the mil dots to hit out to 600 it's so easy. No adjustments needed View Quote Yeah holdovers are the shit. Fuck spinning those turrets. Zero at 100 and use your reticle for how it was intended to be used. |
|
http://www.ar15.com/forums/t_1_5/1604816_Gentle_Propositions____BOOK_IS_LIVE_ON_AMAZON___.html
|
Originally Posted By phatcatblues: I've been reading this thread for quite sometimes, finally got the fnh lower and HCS mod1 upper from kev. I am looking to get leupold 112633 TS30a2, however I am not sure which one has the mk12 mod1 bdc turret and which one has the 7.62mm 168gr bdc. They both use the same 112633 part number, most of the reseller just copy and pasted the description from leupold. I called couple place this afternoon, opticplanet, amazon, and midwayusa, no one knows. Thanks View Quote |
|
|
OEF 10-11
|
Originally Posted By plante74:
Heyyyyyy I agree with everyone's suggestion on holdovers, however. View Quote View All Quotes View All Quotes Originally Posted By plante74:
Originally Posted
Those m1 turrets tho so ugly In all honesty, once you zero an mr/t scope with mk262 at 100, you just use the mil dots to hit out to 600 it's so easy. No adjustments needed I agree with everyone's suggestion on holdovers, however. But it true.... |
|
-Only two defining forces have ever offered to die for you, Jesus Christ and the American G.I. ~ One died for your soul, the other for your freedom.
|
Originally Posted By gunnut003:
But it true.... View Quote View All Quotes View All Quotes Originally Posted By gunnut003:
Originally Posted By plante74:
Originally Posted
Those m1 turrets tho so ugly In all honesty, once you zero an mr/t scope with mk262 at 100, you just use the mil dots to hit out to 600 it's so easy. No adjustments needed I agree with everyone's suggestion on holdovers, however. But it true.... While not as girthy as the M2's and 3's, they are longer... Which could have it's advantages.... |
|
|
Where the F are all the ARMS rings? Any leads on M or H?
I sent off my MO for the 3.5-10...but I'll be forced to use EGW rings instead |
|
|
http://www.ar15.com/forums/t_1_5/1604816_Gentle_Propositions____BOOK_IS_LIVE_ON_AMAZON___.html
|
Originally Posted By RTUtah:
Del-Ton has Highs last I checked, but they have lever-stops. View Quote View All Quotes View All Quotes Originally Posted By RTUtah:
Originally Posted By Mattyvac:
Where the F are all the ARMS rings? Any leads on M or H? I sent off my MO for the 3.5-10...but I'll be forced to use EGW rings instead Del-Ton has Highs last I checked, but they have lever-stops. sold out |
|
|
Originally Posted By Mattyvac: Originally Posted By RTUtah: Originally Posted By Mattyvac: Where the F are all the ARMS rings? Any leads on M or H? I sent off my MO for the 3.5-10...but I'll be forced to use EGW rings instead Del-Ton has Highs last I checked, but they have lever-stops. sold out Dang. That's all I got.
|
|
http://www.ar15.com/forums/t_1_5/1604816_Gentle_Propositions____BOOK_IS_LIVE_ON_AMAZON___.html
|
FYI, SWFA is listing the TS-30A2 on their site. If you scroll through the Leupold Tactical scopes - MR/T section the TS-30A2 with correct model number is listed.
http://swfa.com/Leupold-25-8x36-Mark-4-MRT-30mm-Riflescope-P52988.aspx |
|
|
ARMS rings have been becoming increasingly hard to get over the last three or four months. For me, the Mediums dried up first, now the Highs are gone too. I can still find Low's but I can't find anyone who wants them, hahahaha.
I heard from a girl, who probably heard from a guy, who probably heard from like three other people before them (so take that for what it's worth!) that ARMS had to scrap a whole batch of them for some reason or another. That's why we have this dry spell. Who knows? |
|
|
|
Originally Posted By tacticalcoyote:
swfa has rings and there are 2 listings on gunbroker http://swfa.com/ARMS-Scope-Rings-C591.aspx View Quote View All Quotes View All Quotes Originally Posted By tacticalcoyote:
Originally Posted By Mattyvac:
Where the F are all the ARMS rings? Any leads on M or H? I sent off my MO for the 3.5-10...but I'll be forced to use EGW rings instead swfa has rings and there are 2 listings on gunbroker http://swfa.com/ARMS-Scope-Rings-C591.aspx You'd want to call SWFA first, it's one of the things about them you have to do to be sure it's actually in stock. |
|
|
Originally Posted By secretwheelman:
Has anyone ordered aervoe through DSG? I have convinced myself to paint the old mod0 but, there is no way in hell I'm paying $41.56 for shipping on $30.30 worth of paint. http://i1008.photobucket.com/albums/af204/secretwheelman/100_1116_zpsbfb5bd37.jpg View Quote That's the only place I've bought all of my Aervoe. The HAZMAT fees are a killer, so I bought a few extra cans to help offset the cost. |
|
Squire
CVMA Chapter 24-2 |
Originally Posted By SecretSquirell:
That's the only place I've bought all of my Aervoe. The HAZMAT fees are a killer, so I bought a few extra cans to help offset the cost. View Quote View All Quotes View All Quotes Originally Posted By SecretSquirell:
Originally Posted By secretwheelman:
Has anyone ordered aervoe through DSG? I have convinced myself to paint the old mod0 but, there is no way in hell I'm paying $41.56 for shipping on $30.30 worth of paint. http://i1008.photobucket.com/albums/af204/secretwheelman/100_1116_zpsbfb5bd37.jpg That's the only place I've bought all of my Aervoe. The HAZMAT fees are a killer, so I bought a few extra cans to help offset the cost. Go to Home Depot and buy some Krylon........Problem solved. |
|
-Nemo me impune lacesset.
-Beware the fury of a patient man. -Thousands and thousands of laws....All for just ten commandments. -"alot" is not a word. |
Originally Posted By Engineer5:
Go to Home Depot and buy some Krylon........Problem solved. View Quote View All Quotes View All Quotes Originally Posted By Engineer5:
Originally Posted By SecretSquirell:
Originally Posted By secretwheelman:
Has anyone ordered aervoe through DSG? I have convinced myself to paint the old mod0 but, there is no way in hell I'm paying $41.56 for shipping on $30.30 worth of paint. http://i1008.photobucket.com/albums/af204/secretwheelman/100_1116_zpsbfb5bd37.jpg That's the only place I've bought all of my Aervoe. The HAZMAT fees are a killer, so I bought a few extra cans to help offset the cost. Go to Home Depot and buy some Krylon........Problem solved. Krylon doesn't come in the beautiful shade of Field Drab |
|
Squire
CVMA Chapter 24-2 |
Originally Posted By SecretSquirell:
Krylon doesn't come in the beautiful shade of Field Drab View Quote View All Quotes View All Quotes Originally Posted By SecretSquirell:
Originally Posted By Engineer5:
Originally Posted By SecretSquirell:
Originally Posted By secretwheelman:
Has anyone ordered aervoe through DSG? I have convinced myself to paint the old mod0 but, there is no way in hell I'm paying $41.56 for shipping on $30.30 worth of paint. http://i1008.photobucket.com/albums/af204/secretwheelman/100_1116_zpsbfb5bd37.jpg That's the only place I've bought all of my Aervoe. The HAZMAT fees are a killer, so I bought a few extra cans to help offset the cost. Go to Home Depot and buy some Krylon........Problem solved. Krylon doesn't come in the beautiful shade of Field Drab Only Martha Stewart cares about that. Not high speed low drag operators of the MK12 forum. |
|
-Nemo me impune lacesset.
-Beware the fury of a patient man. -Thousands and thousands of laws....All for just ten commandments. -"alot" is not a word. |
|
Originally Posted By Zakk101abn:
Fulton Armory has L's in stock. If using a x36-40 they should clear just fine. View Quote View All Quotes View All Quotes Originally Posted By Zakk101abn:
Originally Posted By Mattyvac:
Where the F are all the ARMS rings? Any leads on M or H? I sent off my MO for the 3.5-10...but I'll be forced to use EGW rings instead Fulton Armory has L's in stock. If using a x36-40 they should clear just fine. Except you won't be able to see through the scope because the eye box won't be visible with the scope that low |
|
|
Originally Posted By Mattyvac:
Except you won't be able to see through the scope because the eye box won't be visible with the scope that low View Quote View All Quotes View All Quotes Originally Posted By Mattyvac:
Originally Posted By Zakk101abn:
Originally Posted By Mattyvac:
Where the F are all the ARMS rings? Any leads on M or H? I sent off my MO for the 3.5-10...but I'll be forced to use EGW rings instead Fulton Armory has L's in stock. If using a x36-40 they should clear just fine. Except you won't be able to see through the scope because the eye box won't be visible with the scope that low The only way you'd get away with it is with using a riser of some sort, either and S-EX or something similar on a MOD 1. For MOD H's with the RECCE rail they should be perfect. |
|
|
Originally Posted By Engineer5: Only Martha Stewart cares about that. Not high speed low drag operators of the MK12 forum. View Quote View All Quotes View All Quotes Originally Posted By Engineer5: Originally Posted By SecretSquirell: Originally Posted By Engineer5: Originally Posted By SecretSquirell: Originally Posted By secretwheelman: Has anyone ordered aervoe through DSG? I have convinced myself to paint the old mod0 but, there is no way in hell I'm paying $41.56 for shipping on $30.30 worth of paint. http://i1008.photobucket.com/albums/af204/secretwheelman/100_1116_zpsbfb5bd37.jpg That's the only place I've bought all of my Aervoe. The HAZMAT fees are a killer, so I bought a few extra cans to help offset the cost. Go to Home Depot and buy some Krylon........Problem solved. Krylon doesn't come in the beautiful shade of Field Drab Only Martha Stewart cares about that. Not high speed low drag operators of the MK12 forum. Absolutely goddamn right.
|
|
http://www.ar15.com/forums/t_1_5/1604816_Gentle_Propositions____BOOK_IS_LIVE_ON_AMAZON___.html
|
X-Posting from the Retro section!
Looks like McKay is now doing A1 style lowers. Here's the thread: Aparently the first run has selector markings on the right side but next batch won't. If you're wanting an A1 profile and don't care as much about that, they're $139 per. From the next bench over it would certainly pass the sniff test of most any fellow Mk12 Cloner (As long as it's rattle canned. Failure to do so would result in closer scrutiny and ridicule, possibly teabagging in your sleep). |
|
|
Originally Posted By lancecriminal86:
X-Posting from the Retro section! Looks like McKay is now doing A1 style lowers. Here's the thread: Aparently the first run has selector markings on the right side but next batch won't. If you're wanting an A1 profile and don't care as much about that, they're $139 per. From the next bench over it would certainly pass the sniff test of most any fellow Mk12 Cloner (As long as it's rattle canned. Failure to do so would result in closer scrutiny and ridicule, possibly teabagging in your sleep). View Quote I applaud them for bringing another A1 option to the table, but they're going to have to do a bit better. At least in that image, they're using forgings where the A2 reinforcement doesn't extend all the way to the rear of the receiver. So when it's milled down to A1 profile, it's still doesn't have an accurate profile. Forward from the rear and slanted. Other forgings are better candidates for reprofiling. Hope to see them switch to them. Again, always nice to see more options. |
|
|
K, I know this has been covered before, but with a 547+ page thread, the time to find it will bring me to a new decade.....
What is the correct sling for a MOD 0 / SPR A/B? I have the butt-stock piece that came with our kits when they were fielded circa 2001ish, but the make, model, etc of the slings that are long since gone is eluding me. Any Idears? |
|
|
Originally Posted By 18E3V:
K, I know this has been covered before, but with a 547+ page thread, the time to find it will bring me to a new decade..... What is the correct sling for a MOD 0 / SPR A/B? I have the butt-stock piece that came with our kits when they were fielded circa 2001ish, but the make, model, etc of the slings that are long since gone is eluding me. Any Idears? View Quote eagle tas-1-umss http://www.cheaperthandirt.com/product/EAG-121 |
|
|
Anyone have a good duracoat or kryon color that matches PRI's dark earth free float tube?
|
|
|
Originally Posted By secretwheelman:
Originally Posted By phatcatblues:
I've been reading this thread for quite sometimes, finally got the fnh lower and HCS mod1 upper from kev. I am looking to get leupold 112633 TS30a2, however I am not sure which one has the mk12 mod1 bdc turret and which one has the 7.62mm 168gr bdc. They both use the same 112633 part number, most of the reseller just copy and pasted the description from leupold. I called couple place this afternoon, opticplanet, amazon, and midwayusa, no one knows. Thanks Got it, Thanks. BTW swfa rings are back ordered. |
|
|
View Quote View All Quotes View All Quotes Originally Posted By Mattyvac:
Originally Posted By 18E3V:
K, I know this has been covered before, but with a 547+ page thread, the time to find it will bring me to a new decade..... What is the correct sling for a MOD 0 / SPR A/B? I have the butt-stock piece that came with our kits when they were fielded circa 2001ish, but the make, model, etc of the slings that are long since gone is eluding me. Any Idears? eagle tas-1-umss http://www.cheaperthandirt.com/product/EAG-121 I think that's the issued one for the Mod 1. Do we know if it was specified for the earlier versions too? I'd just say run what works, Someone else here got the Eagle and said it was crap to actually use, only useful for clone points. You could always build your own sling, aparently the VTAC and Vicker's slings came from them using old alice pack adjusters and M60 slings or something, I think that fits the spirit for an early Mod 0 in the 2001 timeframe. |
|
|
Originally Posted By Hunterex:
I applaud them for bringing another A1 option to the table, but they're going to have to do a bit better. At least in that image, they're using forgings where the A2 reinforcement doesn't extend all the way to the rear of the receiver. So when it's milled down to A1 profile, it's still doesn't have an accurate profile. Forward from the rear and slanted. Other forgings are better candidates for reprofiling. Hope to see them switch to them. Again, always nice to see more options. View Quote View All Quotes View All Quotes Originally Posted By Hunterex:
Originally Posted By lancecriminal86:
X-Posting from the Retro section! Looks like McKay is now doing A1 style lowers. Here's the thread: Aparently the first run has selector markings on the right side but next batch won't. If you're wanting an A1 profile and don't care as much about that, they're $139 per. From the next bench over it would certainly pass the sniff test of most any fellow Mk12 Cloner (As long as it's rattle canned. Failure to do so would result in closer scrutiny and ridicule, possibly teabagging in your sleep). I applaud them for bringing another A1 option to the table, but they're going to have to do a bit better. At least in that image, they're using forgings where the A2 reinforcement doesn't extend all the way to the rear of the receiver. So when it's milled down to A1 profile, it's still doesn't have an accurate profile. Forward from the rear and slanted. Other forgings are better candidates for reprofiling. Hope to see them switch to them. Again, always nice to see more options. Well, it's better than I could do trying to ghetto grind an A2 or an 80% myself. I don't know when NDS is doing its next run but I'd rather be able to get something immediately when funds appear, trying to set cash aside doesn't seem to work at the rate we are having to spend $$$ on non-gun things. If they sell well enough perhaps they can improve the grind profile on their next round. What else needs to change in the rear of the receiver? |
|
|
Got my EGW scope rings and they're too short
So I guess it's on to NF Ultralight rings? The ARMS H rings are 1.45" above the rail, the larue SPR mount is 1.5" above the rail, and NF makes ultralight rings in 1.265" and 1.375" above the rail....decisions... |
|
|
Originally Posted By lancecriminal86:
I think that's the issued one for the Mod 1. Do we know if it was specified for the earlier versions too? I'd just say run what works, Someone else here got the Eagle and said it was crap to actually use, only useful for clone points. You could always build your own sling, aparently the VTAC and Vicker's slings came from them using old alice pack adjusters and M60 slings or something, I think that fits the spirit for an early Mod 0 in the 2001 timeframe. View Quote View All Quotes View All Quotes Originally Posted By lancecriminal86:
Originally Posted By Mattyvac:
Originally Posted By 18E3V:
K, I know this has been covered before, but with a 547+ page thread, the time to find it will bring me to a new decade..... What is the correct sling for a MOD 0 / SPR A/B? I have the butt-stock piece that came with our kits when they were fielded circa 2001ish, but the make, model, etc of the slings that are long since gone is eluding me. Any Idears? eagle tas-1-umss http://www.cheaperthandirt.com/product/EAG-121 I think that's the issued one for the Mod 1. Do we know if it was specified for the earlier versions too? I'd just say run what works, Someone else here got the Eagle and said it was crap to actually use, only useful for clone points. You could always build your own sling, aparently the VTAC and Vicker's slings came from them using old alice pack adjusters and M60 slings or something, I think that fits the spirit for an early Mod 0 in the 2001 timeframe. There have been pics with it used with the Mod 0. I agree with whoever said it sucks I have one but only for clone purposes. ETA- I pretty sure this is one on this Mod 0, " /> |
|
|
Originally Posted By lancecriminal86:
Well, it's better than I could do trying to ghetto grind an A2 or an 80% myself. I don't know when NDS is doing its next run but I'd rather be able to get something immediately when funds appear, trying to set cash aside doesn't seem to work at the rate we are having to spend $$$ on non-gun things. If they sell well enough perhaps they can improve the grind profile on their next round. What else needs to change in the rear of the receiver? View Quote View All Quotes View All Quotes Originally Posted By lancecriminal86:
Originally Posted By Hunterex:
Originally Posted By lancecriminal86:
X-Posting from the Retro section! Looks like McKay is now doing A1 style lowers. Here's the thread: Aparently the first run has selector markings on the right side but next batch won't. If you're wanting an A1 profile and don't care as much about that, they're $139 per. From the next bench over it would certainly pass the sniff test of most any fellow Mk12 Cloner (As long as it's rattle canned. Failure to do so would result in closer scrutiny and ridicule, possibly teabagging in your sleep). I applaud them for bringing another A1 option to the table, but they're going to have to do a bit better. At least in that image, they're using forgings where the A2 reinforcement doesn't extend all the way to the rear of the receiver. So when it's milled down to A1 profile, it's still doesn't have an accurate profile. Forward from the rear and slanted. Other forgings are better candidates for reprofiling. Hope to see them switch to them. Again, always nice to see more options. Well, it's better than I could do trying to ghetto grind an A2 or an 80% myself. I don't know when NDS is doing its next run but I'd rather be able to get something immediately when funds appear, trying to set cash aside doesn't seem to work at the rate we are having to spend $$$ on non-gun things. If they sell well enough perhaps they can improve the grind profile on their next round. What else needs to change in the rear of the receiver? They did really well in the reprofiling, it just wasn't a good forging to use for the purpose. Although it's probably the most common style now. |
|
|
so, ive seen the noveske 16" recon barrels are back in stock. $430 is a ton of money. i know its correct for the Mod H (which is my plan), but for the money im throwing into this rifle, is this the best barrel? is a douglas or krieger going to be THAT much better if im looking to shoot <600 yards? are the noveske barrels worth the scratch or are they over priced for what they are? i would expect it to hold <1 MOA all day for that price.
|
|
"I suggest you give the tampons back to your sister and spend some of your cigarette money on trauma dressings."
|
i'd say at least $100 of the price is because Noveske.
if you're a clone perfectionist, go for it. if you're not, a criterion/douglas/krieger from CLE will probably make you happier because you spent less. |
|
tweeter:
After work today I'm gonna take off my pants and start this revolution. |
Originally Posted By NapeSticksToKids:
so, ive seen the noveske 16" recon barrels are back in stock. $430 is a ton of money. i know its correct for the Mod H (which is my plan), but for the money im throwing into this rifle, is this the best barrel? is a douglas or krieger going to be THAT much better if im looking to shoot <600 yards? are the noveske barrels worth the scratch or are they over priced for what they are? i would expect it to hold <1 MOA all day for that price. View Quote You're gonna have to send the noveske to ADCO for the collar step so add $150 there too on top of that |
|
|
Only Martha Stewart cares about that. Not high speed low drag operators of the MK12 forum. View Quote View All Quotes View All Quotes Only Martha Stewart cares about that. Not high speed low drag operators of the MK12 forum. Absolutely goddamn right. |
|
OEF 10-11
|
Originally Posted By RTUtah: Absolutely goddamn right. View Quote View All Quotes View All Quotes Originally Posted By RTUtah: Originally Posted By Engineer5: Originally Posted By SecretSquirell: Originally Posted By Engineer5: Originally Posted By SecretSquirell: That's the only place I've bought all of my Aervoe. The HAZMAT fees are a killer, so I bought a few extra cans to help offset the cost. Go to Home Depot and buy some Krylon........Problem solved. Krylon doesn't come in the beautiful shade of Field Drab Only Martha Stewart cares about that. Not high speed low drag operators of the MK12 forum. Absolutely goddamn right. |
|
|
Got my ARMS scope rings from Del-Ton. All I need now is a scope.
|
|
|
|
Originally Posted By Mattyvac:
I got one for you in the EE View Quote View All Quotes View All Quotes Originally Posted By Mattyvac:
Originally Posted By WTFShane:
Got my ARMS scope rings from Del-Ton. All I need now is a scope. I got one for you in the EE I got one too.... http://m.ebay.com/itm?itemId=271544654746 For some reason you have to copy and paste the link for it to work... |
|
|
I also have a BNIB Bison Armory 16" stainless Recon barrel I'm getting rid of if anyone wants first dibs before I let it out in the EE. Took me about a month to get, even though they say "in stock".
|
|
|
Originally Posted By Zakk101abn:
I got one too.... http://m.ebay.com/itm?itemId=271544654746 For some reason you have to copy and paste the link for it to work... View Quote View All Quotes View All Quotes Originally Posted By Zakk101abn:
Originally Posted By Mattyvac:
Originally Posted By WTFShane:
Got my ARMS scope rings from Del-Ton. All I need now is a scope. I got one for you in the EE I got one too.... http://m.ebay.com/itm?itemId=271544654746 For some reason you have to copy and paste the link for it to work... Damn. Nice price. |
|
|
Originally Posted By Zakk101abn:
I got one too.... http://m.ebay.com/itm?itemId=271544654746 For some reason you have to copy and paste the link for it to work... View Quote View All Quotes View All Quotes Originally Posted By Zakk101abn:
Originally Posted By Mattyvac:
Originally Posted By WTFShane:
Got my ARMS scope rings from Del-Ton. All I need now is a scope. I got one for you in the EE I got one too.... http://m.ebay.com/itm?itemId=271544654746 For some reason you have to copy and paste the link for it to work... Wow it had illum too. Someone got a steal |
|
|
Where can I find a black KAC front sight. I keep finding the taupe one. I greatly appreciated the helps gents!
|
|
СвД
|
Hey guys...so I'll admit, I'm new to this site. I recently started building an MK12 and so far the most difficult part for me is which rail system to go with. I would love to have a Knights Armament free floating RAS, but I think I have better luck winning the lottery. Does anyone have any advice on what to do for a rail?
Thanks! |
|
|
Build a mod 0 and use the pri rail. I got ultra lucky when I scored my rail..... Yeah u know who u are
|
|
|
Originally Posted By mlhenning9625: Hey guys...so I'll admit, I'm new to this site. I recently started building an MK12 and so far the most difficult part for me is which rail system to go with. I would love to have a Knights Armament free floating RAS, but I think I have better luck winning the lottery. Does anyone have any advice on what to do for a rail? Thanks! View Quote Quickest, easiest, sexiest way to get in the game is with a Holland. Build another upper when you can find the parts. |
|
http://www.ar15.com/forums/t_1_5/1604816_Gentle_Propositions____BOOK_IS_LIVE_ON_AMAZON___.html
|
Sign up for the ARFCOM weekly newsletter and be entered to win a free ARFCOM membership. One new winner* is announced every week!
You will receive an email every Friday morning featuring the latest chatter from the hottest topics, breaking news surrounding legislation, as well as exclusive deals only available to ARFCOM email subscribers.
AR15.COM is the world's largest firearm community and is a gathering place for firearm enthusiasts of all types.
From hunters and military members, to competition shooters and general firearm enthusiasts, we welcome anyone who values and respects the way of the firearm.
Subscribe to our monthly Newsletter to receive firearm news, product discounts from your favorite Industry Partners, and more.
Copyright © 1996-2024 AR15.COM LLC. All Rights Reserved.
Any use of this content without express written consent is prohibited.
AR15.Com reserves the right to overwrite or replace any affiliate, commercial, or monetizable links, posted by users, with our own.